Produse pentru epoxidharz (228)

Syntech Epox Timber Syntech Epox Timber is a liquid, transparent, two-component epoxy resin for incorporating thick objects, mass filled casting and the treatment of wood. Its self-levelling and non-yellowing nature, along with its scratch-resistance and fluid consistency, render it ideal for pouring and for filling any voids. The final effect of Syntech Epox Timber is a smooth and even surface with a transparency similar to glass. It is also possible to colour the product with specific pigments to achieve a coloured transparent effect. It is advisable to conduct preliminary tests to achieve the desired aesthetic effect. Syntech Epox Timber can be applied in thicknesses from 0.5 to 10 cm for the creation of tables and shelves in wood and resin, artistic creations and high thickness castings in which to incorporate small parts, stones, shells and objects in general, including metal . Higher thicknesses and castings without inserting embedded objects can cause overheating during the catalysis of the product. Syntech Epox Timber has excellent chemical resistance, abrasion, scratches and wear, has a high degree of transparency that lasts over time thanks to UV filters, the self-leveling consistency and low viscosity facilitate the elimination of bubbles air and allow to obtain planar surfaces, it does not contain solvents. Excellent resistance to water, basic solutions. Fair resistance to acids and solvents. Syntech Epox Timber is a transparent vitrifying resin to be applied by pouring for the construction of tables and wood-resin surfaces, by incorporating boards, fragments or sections of wood, even irregular, appropriately treated and thick coatings on even wood surfaces. If the support is absorbent, such as untreated wood or porous materials, it must be previously treated with the same Syntech Epox Timber applied by brush to avoid the formation of air bubbles. To make bulk filler castings, prepare suitable molds of the desired shape. Make sure you have 'leveled' the surface so that the resin can level itself correctly and thus a perfectly flat surface is obtained. Mix components A (basic formulation) and B (hardener) each in their own container before mixing; then pour component B into the container of component A. Mix everything for a few minutes using a mechanical stirrer at variable speed until a homogeneous mixture is obtained, with a uniform color and free of lumps. Do not take partial quantities from the packs to avoid any errors in the mixing ratio which would cause failure or incomplete hardening. After mixing, proceed by pouring the mixture into the previously prepared mold. High thickness castings require hardening times between 48-72 hours at a temperature of 25-30 ° C. To avoid surface defects or lengthening of the hardening time, it is advisable to work in an environment with a temperature of at least 25 ° C, a temperature to be maintained throughout the hardening period. The completely hardened product can be polished like normal lacquers paying attention to the residual elasticity, during the polishing process it is necessary to avoid overheating the surface to avoid temporary softening. Otherwise, you can proceed with the application of clear acrylics after having sanded the resin with 500/1000 paper. Approximately 11 kg / m² of Syntech Epox Timber for each centimeter of thickness to be created (approximately 1100 kg for each cubic meter). PACKAGING AND DIMENSIONS: Pail 0.7 kg [A] - Pail 3.5 kg [A] - Pail 0.3 kg [B] - Pail 1.5 kg [B] - Kit: 1 Pail 0.7 kg [A] + 1 Pail 0.3 kg [B] - Kit: 1 Pail 3.5 kg [A] + 1 Pail 1.5 kg [B]

Die perfekte Industriebodenbeschichtung mit Epoxidharz für stark frequentierte Bereiche in nur einem Anstrich: Robust, langlebig und chemikalienbeständig! Verfügbar in vielen Farben und Variationen!

Araldite® AY 105-1 / Härter HY 991 Zweikomponenten-Flüssig-Epoxidkleber Araldite® AY 105-1 / Härter HY 991 ist ein vielseitiger, zweikomponentiger, bei Raumtemperatur härtender, fließfähiger Klebstoff. von hoher Festigkeit und Umweltbeständigkeit.Es eignet sich für die Verbindung einer Vielzahl von Metallen, Keramiken, Glas, Gummi, Hartkunststoffen und den meisten anderen Materialien, die häufig verwendet werden. - Mittelviskose fließfähige Flüssigkeit- Gute Leistung bis >100°C- Hervorragende Wasser- und Feuchtigkeitsbeständigkeit - Gute chemische Beständigkeit Steckbrief: ARALDITE Bezeichnung AY105‐1 HY991 Chemische Basis, Mischungsverhältnis 2K EP 2:1 Farbe hellbraun Viskosität (Verarbeitung) 15 Pa×s Verarbeitungszeit für 100g bei 23°C 45min Typische Tg Glasübergangstemperatur 100°C Temp. Beständigkeit (ZSF von 5N/mm² ) 120°C Shore‐Härte Bruchdehnung bei 23°C E‐Modul in MPa bei 23°C Biegefestigkeit MPa (ISO 178) Zugfestigkeit (ISO 527) bei 23°C Schälfestigkeit (ISO 4578) Alu EAN:4260534181743 kg:1

Das Epoxidharz-System E30RB ist eine 2K Epoxi-Rollbeschichtung mit mittlerer Verarbeitungszeit für hochwertige Boden- und Wandbeschichtungen ähnlich RAL7032 kieselgrau.

ThermoPL-152 ist ein flammhemmender Verbundwerkstoff auf der Basis von Epoxidharz mit hoher Haftung und Zuverlässigkeit. Er wird hauptsächlich in IC-, Transistor-, Dioden-, Netzwerktransformator- und anderen Halbleiterkapselungen verwendet. Es bietet die Vorteile einer kompakten Verpackungsgröße, eines geringen Gewichts, einer einfachen Struktur, eines bequemen Verfahrens, einer guten chemischen Beständigkeit und einer elektrischen Isolationsleistung sowie einer hervorragenden mechanischen Leistung. Insbesondere im Vergleich zu herkömmlichen Einkapselungsmaterialien bietet die höhere Wärmeleitfähigkeit das Aussprechen von Potentialen in verschiedenen Ebenen von Hochleistungselektronikverpackungen. Herkunftsland:China

Cette gamme de revêtements de sol semi-épais à base de résine époxy est recommandé pour les sols devant subir des sévères sollicitations mécaniques et d'usure : entrepôts de manutention et de stockage, salles des machines, halls de montage et toutes surfaces sollicitées par un trafic lourd. Caractéristiques : Résistance à l’abrasion ; Résistance aux chocs ; Sans joints ; Surface texturée (sans bouche pore ni finition) ; Surface pouvant être finie par un autre système Himfloor. Caractéristiques techniques : Epaisseur : à partir de 5 mm minimum ; suivant les systèmes et le poids coulé au m², l’épaisseur peut aller jusqu’à 30 mm. Couleur : couleur RAL Aspect : texturé ou semi-lisse Finition : mate ou brillante Options : Rattrapage épaisseur Mise en œuvre : truellable

Epoksi masalar usta eller tarafından üretilmektedir. Bu masa modellerinde en dikkat çekici özellik, aynı modelin bir daha aynısının çıkmamasıdır. Her ürettiğimiz model sadece sizlere özel olmaktadır. Asırlık olan zeytin ve ceviz ağaçlarından ürettiğimiz epoksi ürünler edinmek için bize ulaşabilirsiniz. Firmamız epoksi masa üretiminde 25 yıllık bir tecrübeye sahiptir. Epoksi masalarımız için ürünlerimizi inceleyebilir, bizlerle numaralarımızdan ulaşabilirsiniz. Mekan tasarımlarında eşsiz imkanlar sunabilen doğal reçine epoksi ürünleriyle günümüzde en güzel masa, sandalye, sehpa, ev ünitesi ürünleri tasarlamaktayız. Alışılmışın dışında yıllarca kullanabileceğiniz epoksi masalara sahip olmak için bize numaralarımızdan ulaşabilirsiniz.

ACTANDU20 est utilisé en association avec une résine époxyde en émulsion aqueuse, solide ou liquide, pour la production de couche primaire à deux composants pour aluminium et acier galvanisé. Ces formules offrent une flexibilité exceptionnelle et une excellente adhérence humide et sèche. Aucune réactivité ou formation de bulles n’est observée sur acier galvanisé. Associé à une résine époxyde liquide, il est possible de formuler un système exempt de COV pour application sur galvanisé avec de très bonnes performances dans différents environnements, par exemple C5-1 et C5-M en référence aux normes ISO12944-6. Combiné à une résine époxyde BPA/BPF, ce produit est utilisé pour la fabrication de couche primaire à l’eau applicable sur supports absorbants et non-absorbants de matériaux de construction. Des formules d’orientation sont disponibles avec résines époxydes liquides et solides.

Acrylat-Strukturklebstoff, schnellhärtend

Bei der Förderung von stark gefüllten, hochviskosen oder abrasiven Medien – wie gefüllten Klebstoffen, gefüllten Silikonen oder gefüllten Vergussmassen - ist eine Exzenterschneckenpumpe ein Muss.

Hello! We offer Sadhu Boards of our own production as well as other wood products for yoga and not only! Sadhu boards (nail boards) are a wonderful yoga tool that is gaining popularity. Our boards are presented on Etsy and Amazon under the Metadesk brand. We make boards from different base materials (plywood, solid oak, ash, thermal ash, walnut), with different nail materials (galvanized nails (several types), copper, copper, bamboo), different shapes, sizes, nail placement, colors, engraving. Wholesale order - from 10 sets of boards. Delivery from Ukraine (the parcel is delivered by road from Ukraine to Poland). We will be happy to fulfill your order! We can also produce various wood products (wall panels, benches, wall decorations), including epoxy resin, laser engraving. Contact us for more information. Have a nice day :)

İyi Günler Yirmi iki yıllık saha tecrübemizi 2013 yıllında Zebra Yapı ve 2020 yılında Ekoyalıtım firmalarını kurarak taahhüt işlerinde hizmet vermeye başladık. Faaliyet alanlarımız özelikle proje sonrası uygulama işleri ve teknik çözümler sunmak. Aynı anda projede birbirinden farklı sıralı imalatların uygulanmasında takım çalışmasına uyumlu uzman teknik kadrolarımız ile hizmet vermekteyiz.

Epoxy Resin Wall Clock | Handmade Epoxy Product | Souvenir | Gift for Newly Married Couples | Luxury and Cool Wall Clock Create an amazing rustic atmosphere in your home with these Olive Wood & Metallic Color Epoxy Resin Wall Clocks. These unique wall clocks will be perfect matches to your unique decors. These cool clocks will be the most aestethic home decor that you will ever own. Epoxy Resin Wooden Clocks are will be your new favorite piece and a great addition to their wood decor! If you're looking for a fantastic wedding or anniversary gift, or a christmas gift, these lovely & aestethic rustic wood clocks are perfect. You can be sure that everyone who see these amazing pieces will be amazed. Details Each wall clock will be custom made with each new order. This means the wall clock that you buy will be uniquely made just for you. If you want any additions or special lookings for your order, please do not hesitate to contact us.

En partant d’une forme très simple, géométrique , rigide , que l’on force jusqu’à obtenir une nouvelle forme contre intuitive , qu’on multiplie et qu’on assemble en lui laissant la liberté de mouvement , on aboutit à cette structure étrange et belle que vous pourrez manipuler , moduler autant qu’il vous plaira . Cette sculpture mesure 86 cm de hauteur pour une envergure variable de 30 à 60 cm . La couleur blanche de cette sculpture peut être modifiée si vous le désirez . Elle peut aussi être réalisée en sculpture monumentale jusqu’à 2 m de hauteur et 1,50 m d’envergure environ , sur commande uniquement . La couleur des lames reste à votre choix. Référence: sm 760:5 Kg Matière: acier inox:terrasse : Marbre dimensions: H86 .envergure : 60 environ: éléments modulables

ALPHATEC® 170 is a three-component polymer grout system consisting of modified epoxy resin, chemical hardener, and a chemically-modified filler. It is specially formulated for chock grouting to replace the steel packers and liners used under many different types of machinery. ALPHATEC® 170 chock grouting can be used between steel surfaces, or between aggregate-filled epoxy grout and steel bases, in a sandwich approach. ALPHATEC® 170 has been approved by Lloyd’s Register of Shipping (LR) for use in chocking main propulsion engines in marine applications, as well as for miscellaneous deck machinery and auxiliaries. Alphatec Engineering, Epoxy Grout and Concrete Repair Specialists.

Rotafix Zeroset Anchor Grout is a 2-part high strength epoxy system that is used for the fixing of metallic objects into concrete such as anchors and studs. Rotafix Zeroset Anchor Grout has been specifically designed for setting at low temperatures in smooth-walled, diamond drilled holes. This chemical anchor will displace water from a hole then cure under any residual water. This high-performance chemical anchor grout has been approved by the Department of Transport for parapets and street lighting. Additional Information: Compressive Strength: 70N/mm2 Tensile Strength: 16N/mm2 Flex Strength: 32N/mm2 Workable for 20 minutes at 20°C Available Sizes: 500cc (Product code: 3542)

Für Anwendung von 850A bis 6300A / IP68 Schienenverteilersystem für Petrochemie, Nukleare Anlagen, Zementwerke, Kraftwerke, Häfen und Schiffswerften, Lebensmittelbetriebe, Tunnels und Unterführungen

Syntech IC 55 A two-component pure epoxy adhesive that is fluid with a low viscosity, free from fillers and solvents, being specific for high performance structural consolidation injections in crumbling masonry, degraded concrete, aging screeds and industrial flooring, cracked plasters and mortars and so on. It is ideal for securing bars, clamps and tie-rods. It is also perfect for the deep consolidation of wooden materials and other types of porous materials, with impregnation by brush or roller. Reinforcing and filling injections of cracks in concrete, stone, brick, mixed works etc. Anchor, bonding and attachment of connectors, plates etc. Structural reinforcement and small volume rebuilding (only horizontal) in general. Reinforcement of porous construction materials such as wood, natural stone, bricks etc. The surfaces of application will be seasoned and dry (residual humidity measured at a depth of 4 cm, should not be greater than 4 % ), free from dust, grease, soiling, crumbling and non-adhering parts. Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A taking care to remove all the material from the packaging, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mixture is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous lump-free mixture is obtained. Lay the material using the techniques specific to the type of intervention: injection, pouring, brushing, etc.. Do not apply on wet or pulverised media. Non-conformities of the support can have unpleasant drawbacks: detachments, large bubbles, etc. Apply only in the intended thermal intervention (+8/+35 °C). Use the product immediately after mixing and mix only the amount of product intended for immediate use. Syntech IC 55 is a product based on fluid epoxy resins. It may cause variations in the colour of the product on which it is applied, both wood and stone material. For this reason it is recommended to carry out preliminary tests. Approximately 1.1 kg of SYNTECH IC55 for each cubic decimetre of volume to be filled. Can 1 kg [A] - Can 5 kg [A] - Can 0.5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 1 kg [A] + 1 Can 0.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Armaglass Grid 33 Armaglass Grid 33 is a square reinforcement gusset, with a side of 17 cm, made with glass yarn bars and pultruded epoxy resin. The monolithic, bidirectional mesh has a 33x33mm mesh, with a bar diameter of 3mm. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. Armaglass Grid 33 is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with Armaglass Structura meshes in pultruded glass for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Grid 33 is combined. Apply Armaglass Grid 33 together with the Armaglass Connectors provided in the reinforced plastering cycle, in order to guarantee greater structural collaboration between the mesh, connector and mortar of the RINFOR SYSTEM reinforcement system. Based on the connectors provided in the CRM system. Packaging: Bulk from 1 piece UM: €/piece

Syntech Acid Resistant Chemical-resistant coating based on modified epoxy phenolic resins, for the protection of walls, floors and concrete, steel and fiberglass structures. Two-component epoxy phenolic resin, applicable by spray, roller or spatula, for the coating and waterproof protection of structures subject to strong chemical aggression. Property: high mechanical and abrasion resistance, high adhesion to surfaces good elasticity high chemical resistance to acids, bases and solvents very high tenacity and ease of cleaning and maintenance high chemical resistance to petrol, fuels and hydraulic oil applicable in thick layers, even several times. Industrial floors in concrete. Waste water purification tanks and related technical rooms. Tanks, ducts and food containers. Digesters and plants for the production of biogas. Coating of pipes and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containment tanks for accidental spills of petroleum products, chemicals and food products. Protective coating of floors and walls of food, dairy, wine, breweries, distilleries, oil mills, oil mills. As a primer: 0.20 - 0.25 kg of Syntech Acid Resistant for each square meter of surface to be primed. As a coating: 0.40 kg of Syntech Acid Resistant for each square meter of surface to be coated. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Syntech Bioflex Anti-acid coating based on modified epoxy and polysulphide polymers, for the waterproof coating of concrete and steel tanks, tanks and containment tanks. High mechanical and abrasion resistance High adhesion to surfaces Good elasticity High chemical resistance to acids, bases and solvents Very high tenacity and ease of cleaning and maintenance Applicable to heavy thicknesses. Anti-acid waterproofing protective coating for the chemical industry Internal and external lining of tanks, tanks, cisterns, towers, pylons, etc. Waterproof protective coating of digesters of biogas and purification plants Anti-acid protective coating for sewers, secondary tanks, sewer collectors, channels and ducts intended for the containment of waste water and drainage Anti-acid coating of fiberglass tanks for the chemical industry. From 0.40 to 0.50 kg of Syntech Bioflex for each square meter of surface to be covered, applied in two coats. Can 6.1 kg [A] - Can 3.9 kg [B] - Kit: 1 Can 6.1 kg [A] + 1 Can 3.9 kg [B]

Syntech AS 31 The two-component structural epoxy adhesive putty is soft, thixotropic and spatulable (malleable paste), ideal for anchoring steel connectors, hermetically sealing through-holes in concrete, bonding steel plates on concrete surfaces, as an accessory product for laying road joints, for the reconstruction of wooden beam heads, repairing cracks and reconstructing missing geometries, fixing injectors, reconstructing joints in concrete flooring and fixing Elastotex 250 Combi elastic strips, including when in contact with water destined for human consumption. Structural reinforcements of structural elements (beams, pillars, etc.) by bonding steel sheets to the concrete. Reconstruction of joints in concrete floorings. Rigid structural bonding (beton plaque) of prefabricated elements and of articles in different building materials: concrete, steel, glass, wood, marble, tiles, stones etc. Anchoring, bonding and attachment of connectors, ties etc. Attachment of elastic straps for waterproofing joints, Elastotex. Reconstruction of wooden heads, crack repair, reconstruction of missing geometries on various supports. The application surfaces must be suitably prepared and adequately resistant: free from dust, grease, soiling, crumbling and non-adhering parts, devoid of wet surface areas. For floorings, moreover, a shot peening or preliminary milling of the surfaces of adhesion is recommended. The metal elements are to be blasted to "almost white metal". Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A, taking care to remove all the material from the packaging and mixing thoroughly with a mixer at a low number of revolutions (or a suitable manual tool), until a homogeneous mixture is obtained, indicated by the uniform colour and the absence of lumps. Apply to the surfaces with the help of spatulas, trowels, etc. Complete the tasks during the useful life of the product. Do not apply in rainy days; do not apply on moist or wet supports; do not apply on pulverised supports; use the product immediately after mixing. Approximately 1.6 kg of Syntech AS 31 for each cubic decimetre of volume to be grouted. Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 0.5 kg [B]

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Syntech Pavicar Two-component coating based on epoxy and polyurethane resins; for the coating, waterproofing and elastic protection of roofs, terraces, pavements, stairs, car parks and surfaces that are cracked or subject to micro-cracks and crazing. High wear resistance Applicable on tarred surfaces and bituminous sheaths Walkable product suitable for covering and waterproofing flat roofs Ease and speed of application with quick intervention times Soft and velvety to the touch Elastic product resistant to dynamic stress Available in two colors. Waterproof coating of concrete, ceramic, porcelain stoneware, wood, sheet metal supports, tarred supports and bituminous sheaths, suitably primed. Creation of elastic and waterproof protections for multi-level parking areas, both internal and external. Ideal for waterproofing cycles of balconies, roofs and terraces as it does not require preliminary demolition work or replacement of coverings. Its application allows the creation of a continuous, elastic and waterproof layer resistant to wear and trampling. Approximately 2.0 kg of Syntech Pavicar for each square meter of surface to be covered, in two coats. Can 8.3 kg [A] - Can 16.7 kg [A] - Can 4.17 kg [A] - Can 1.7 kg [B] - Can 3.3 kg [B] - Can 0.83 kg [B] - Kit: 1 Can 4.17 kg [A] + 1 Can 0.83 kg [B] - Kit: 1 Can 8.3 kg [A] + 1 Can 1.7 kg [B] - Kit: 1 Can 16.7 kg [A] + 1 Can 3.3 kg [B]

Armaglass Corner 33 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh with a side of 33 mm, an ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 33 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 33 is combined. Apply Armaglass Corner 33 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Packaging: Loose from 1.05 meters UM: €/piece

Armaglass Corner 99 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh with a side of 99 mm, an ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 99 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 99 is combined. Apply Armaglass Corner 99 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Based on the total length of the corner areas. Packaging: Loose from 1.05 meters UM: €/piece

Armaglass Corner 66 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh of 66 mm side, ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 66 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 66 is combined. Apply Armaglass Corner 66 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Based on the total length of the corner areas. Packaging: Loose from 1.05 meters UM: €/piece

Araldite 2020 | 0,5 kg Farbloses Zweikomponenten-Klebstoffsystem auf Epoxidharzbasis • Niedrigviskoser, wasserklarer Klebstoff • Besonders gut für Glas und keramische Werkstoffe geeignet • Für farblose Gussteile und Laminate geeignet • Brechungsindex entspricht annähernd demjenigen von Glas Araldite 2020 ist ein bei Raumtemperatur aushärtender, niedrigviskoser Zweikomponentenklebstoff, speziell zum Verbinden von Glas konzipiert. Das System eignet sich zum Verbinden einer Vielzahl von Metallen, Keramik, Glas, Gummi, harten Kunststoffen und der meisten gebräuchlichen Materialien und lässt sich auch auf grossen Flächen mühelos auftragen. Steckbrief: ARALDITE Bezeichnung 2020 Chemische Basis, Mischungsverhältnis 2K EP 3:1 Farbe transparent Viskosität (Verarbeitung) 0,15 Pa×s Verarbeitungszeit für 100g bei 23°C 45min Typische Tg Glasübergangstemperatur 40°C Temp. Beständigkeit (ZSF von 5N/mm² ) 60°C Shore‐Härte Bruchdehnung bei 23°C 0,04 E‐Modul in MPa bei 23°C 2400MPa Biegefestigkeit MPa EAN:4260534180227 g:500

ARALDITE 2011 | 2 kg Arbeitspackung Pastöser Zweikomponentenklebstoff auf Epoxidharzbasis • Allzweck-Klebstoff • Geringe Schrumpfung • Lange Lebensdauer • Gute Beständigkeit gegen dynamische Belastung • Für die Verklebung einer Vielzahl der gebräuchlichsten Materialien Araldite 2011 ist ein bei Raumtemperatur aushärtender, pastöser Allzweck-Zweikomponentenklebstoff. Die Paste zeichnet sich durch gute Kontakthaftung und Zähigkeit aus und eignet sich zum Verbinden einer Vielzahl von Metallen, Keramik, Glas, Gummi, harten Kunststoffen und der meisten gebräuchlichen Materialien. Es handelt sich hier um einen vielseitigen Klebstoff, der sich sowohl für Kunsthandwerker als auch für die meisten industriellen Anwendungen eignet. Steckbrief: ARALDITE Bezeichnung 2011 Chemische Basis, Mischungsverhältnis 2K EP 1:1 Farbe hellgelb Viskosität (Verarbeitung) 30‐45 Pa×s Verarbeitungszeit für 100g bei 23°C 100min Typische Tg Glasübergangstemperatur 45°C Temp. EAN:4260534180043 kg:2