Produse pentru epoxidharz (36)

Syntech Pavisheer A two-component epoxy system based on epoxy resins in aqueous dispersion and solvent-free. It is ideal for completing protective, transparent treatments with a consolidating action and anti-dust effect on industrial concrete flooring, with good mechanical and chemical resistance, especially in reference to contact with oils and solvents. This product also serves well as a primer for casting joints between old and new concrete flooring. Transparent finish of interior floor coverings, mechanical-resistant impregnations, anti-dust and anti-oil for concrete surfaces. The media should have adequate mechanical resistance. The concrete surfaces should be cured, dry, planar and absorbent, free from oils, detergents, powders and soiling. The most appropriate type of mechanical preparation should also be determined (degreasing or shot peening). Conveniently absorbent surfaces may be dealt with directly after a proper cleaning. For tiled surfaces and for pre-existing coverings in resin, a degreasing or shot peening treatment is required until complete opacification and complete elimination of dust. Mix components A and B each in their own container before mixing. Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Pour component B into a suitable container and add component A. Mix everything for a few minutes using a mechanical stirrer with variable speed until a homogeneous and uniform color mixture is obtained. Leave to rest for a few minutes and mix again. Dilute the final product only with water in the Syntech Pavisheer: water ratio of 1: 3 for the first coat and 1: 2 for the second. Gradually add the dilution water, continuing to mix for a few minutes. The dilution ratio can vary according to the porosity of the support; if necessary on closed surfaces it is also possible to dilute the second coat respecting the dilution ratio 1: 3. The Syntech Pavisheer emulsion has a stability of about 2 hours at 20 ° C; within this period the product must be used. Syntech Pavisheer is applied with a short-haired roller or spray, covering the entire surface evenly. We recommend application at temperatures not lower than 5 ° C. From 0.10 to 0.15 kg of SYNTYECH PAVISHEER for each square metre of surface to be covered. Can 5 kg [A] - Canister 1 kg [A] - Can 5 kg [B] - Canister 1 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 1 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B]

Revêtements Époxy Nos revêtements époxy sont réputés pour leur robustesse et leur polyvalence. Ils offrent une excellente adhésion, une résistance chimique et une finition brillante, ce qui les rend idéaux pour les sols, les murs et les machines dans les usines de fabrication, les entrepôts et les installations automobiles.

Epoxy für Industrie- und Gewerbeböden: starke Belastbarkeit; hygienisch zu reinigen; beständig gegen Chlorkohlenwasserstoff, Alkohol, Benzin, Mineralöl, Säuren und Laugen; geeignet für Nassbreiche

Nous sommes ResinPro, une entreprise spécialisée dans la production et la distribution de résines époxy de haute qualité. Notre objectif est d’offrir aux artisans, créateurs, et professionnels un large choix de produits adaptés à tous types de projets, qu’il s’agisse de créations artistiques, de travaux de finition, de revêtements de surface ou d’applications industrielles.

... sind Bodenbeschichtungssysteme auf der Basis von Epoxidharzen, die für Neubau, Sanierung, Modernisierung nahezu alle Fußböden geeignet sind. Entgegen unser Plastifloor®-Bodenbeschichtungen benötigen Plastistone®-Bodenbeschichtungen ca. 1 Woche zur kompletten Aushärtung. Dafür erreichen Sie aber eine höhere chemische Beständigkeit als Plastifloor®-Böden. Plastistone®-Bodenbeschichtungen sind deshalb besonders gut für Bereiche geeignet, in denen mit chemischen Stoffen gearbeitet wird. Hervorzuheben sind Plastisone®-Kiesbodenbeläge, ein sehr dekorativer Boden, der bevorzugt für Ausstellungshallen oder Schwimmbäder verwendet wird.

REFERENCE : AXS03901 couleur:gris. EPOXY 4030 (10+1) 03901.....KG PRODUIT DISPONIBLE UNIQUEMENT SUR COMMANDE DELAI MOYEN 15 JOURS Résine technique chargée aluminium. Moules de thermofomage.

Knöller führt Bodenbeschichtungsarbeiten zum Schutz, der Verstärkungen und der Instandsetzung von Industrieböden mit Epoxidharzen, Polyurethanharzen, Acrylharzen und Polyurethanbeton aus.

Industrial floor painting. Anglia Decor Ltd. Chas accredited for health and safety. Specialist in floor painting, providing nationwide coverage. We prepare the floor using diamond grinding and vacublasting, this ensures the resin coatings adhere well to the floor. Get in touch for a free quote

This grout material was specifically formulated to support heavy machinery on concrete foundations, and when used correctly, will ensure the transfer of static and dynamic loads into the inertia block. The polymer epoxy grouts offered by the Alphatec Group are already extensively tried and proven in many industries around the world. The benefits of using epoxy grouts are most easily seen in a repair or rehabilitation project, but they will perform very well in new installations of all types of rotating machinery. As the only epoxy grout manufacturer with its own contracting arm, Alphatec Engineering is uniquely placed to give you the best combination of products and services.

Nos sols en résine sont conçus pour allier esthétique et performance pour vos maisons, commerces ou encore vos sites industriels. Grâce à une palette variée de couleurs et de finitions, ils se prêtent à une multitude de styles décoratifs et offrent une résistance à toutes épreuves. La durabilité et la facilité d'entretien de nos revêtements de sols en résine font d'eux un investissement judicieux pour un environnement élégant, design et surtout pratique. De plus, ils sont aussi bien utilisés comme revêtement intérieur qu’extérieur !

Le revêtement MORTEX® de type béton ciré est l’enduit de prédilection de ceux qui souhaitent allier technicité, originalité, personnalité et esthétique. Utilisé tant pour ses qualités techniques que pour ses atouts décoratifs, il offre aux projets d’aménagement intérieurs et extérieurs un aspect minéral évoquant le béton ciré ou le béton lissé. Grâce à sa fine épaisseur et à son imperméabilité, le micro-mortier minéral MORTEX® épouse toutes les formes, s’adapte à vos surfaces et offre un look inégalable à vos douches, sols, piscines, escaliers et meubles, tant intérieurs qu’extérieurs. Avec le béton lissé MORTEX®, donnez vie à vos idées les plus créatives.

Auf unserem modern ausgestatteten Maschinenpark mit 12 Spitzgießmaschinen produzieren wir Kunststoffformteile mit einem Schussgewicht von 1g bis 660g.

Syntech Pavicrom SBV Colored two-component finish, permeable to water vapour, based on epoxy resins in water dispersion. Ideal for the pigmented coating of industrial floors and concrete constructions in general with residual humidity and without vapor barrier. Surfaces treated with Syntech Pavicrom SBV are easy to clean and guarantee excellent resistance to mechanical wear, as well as being highly resistant to water, alkaline solutions, detergents and hydrocarbons (petroleum, diesel, petrol, etc.) . Protective and decorative painting of concrete floors, restoration of the color of old resin floors, glazing of wall skirting boards, etc. Ideal for mechanical workshops, manufacturing industries, warehouses and factories in general where high chemical and mechanical resistance is required. It can be used both indoors and outdoors. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating. In case of restoration, use suitable mortars and products suitable for the system beforehand. Wait for the drying times before applying the next coat. The tensile strength must not be less than 1.5 N/mm². Existing paints, coatings or paints, cement grout residues, release agents, oils, greases, silicones, etc. they can be removed mechanically by sandblasting, blasting, hydroblasting or chemical removal. Cracks and fissures In case of static cracks, use Syntech Primer EP-W for sealing. The sealing of dynamic cracks or cracks larger than 4-5 mm must be assessed on site. Generally they can be grouted with elastomeric materials or act as expansion joints. Grouting and spot repairs Any holes or repairs to portions of concrete can be made with mortars from the REPAR line or by applying epoxy mortar made with Syntech Primer EP-W and quartz mastics. Apply a coat of Syntech Primer EP-W as a bonding primer, then proceed to seal and repair the damaged and broken concrete by applying the epoxy mortar. Any small filling of holes and cracks can be done by applying Syntech AS 21 epoxy mortar. Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Primer for concrete Syntech Pavicrom SBV can be applied directly to cementitious substrates as the product diluted with a maximum of 25% by weight of clean water acts as an anchoring primer. Resin coatings The application of Syntech Pavicrom SBV on resinous and multilayer systems must always be preceded by sanding the entire surface to promote and guarantee optimal adhesion of the product to the support. Combine the two components in the indicated mixing ratio. Add component B (hardener) to component A (base) and mix well until a completely homogeneous product is obtained. It is advisable to start mixing briefly with an electric drill at low speed and then intensify the stirring up to a maximum of 300-400 rpm. Leave the emulsion obtained to rest in the container, respecting the following induction times: at 15°C ~ 20 minutes at 25°C ~ 15 minutes at 30°C ~ 10 minutes The product can be applied uniformly using a spray gun or short-haired roller to avoid accumulations of material which could give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area to obtain a uniform film and eliminate any accumulations of product. Apply the first coat of Syntech Pavicrom SBV diluted with a maximum of 25% by weight of clean water as primer. The dilution must be carried out under mechanical stirring, adding the necessary quantity of water at the end of the induction time. Do not dilute the product further during application if it thickens it means that the use time has expired. Create a new emulsion with highly mixed material. Wait at least 12 hours, then apply the second one Colored finish diluted with a maximum of 20% weight of clean water, respecting the consumption and thicknesses indicated. It is possible to create non-slip finishes by adding quartz or hollow glass spheres. From 0.15 to 0.20 kg of Syntech Pavicrom SBV for each square meter of surface to be covered, for each coat. Pail 2.5 kg [A] - Pail 5 kg [A] - Pail 3 kg [B] - Pail 6 kg [B] - Kit: 1 Pail 2.5 kg [A] + 1 Pail 3 kg [B] - Kit: 1 Pail 5 kg [A] + 1 Pail 6 kg [B]

Syntech Epox Level Two-component coloured, high solids, self-levelling and/or multi-layer epoxy coating on concrete surfaces and cementitious substrates. Excellent mechanical and abrasion resistance Wide range of colors available Uniform, glossy finish with possible non-slip finish Excellent mechanical and chemical resistance Excellent resistance to detergents and disinfectants. ▪ Colored abrasion resistant coating ▪ Coating of floors subjected to intense traffic ▪ Coating of floors in laboratories, hospitals, sterile rooms and aseptic rooms ▪ Flooring of warehouses, shopping centres, museums, showrooms, storage and logistics areas ▪ Coating of floors of underground car parks, garages, hangars, automotive and aeronautical industries ▪ Coating of food industry floors ▪ Coating of floors in chemical and pharmaceutical industries. Self-leveling coating SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 Multilayer system 1st layer SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 + 2-3 kg/m2 for waste sowing 2nd layer SYNTECH EPOX LEVEL: 0.5 kg/m2 QUARTZ 0.1-0.5: 0.2 kg/m2 + 2-3 kg/m2 for waste sowing Finish SYNTECH EPOX LEVEL: 0.3 kg/m2 QUARTZ 0.06-0.25: 0.05 kg/m2. Can 10 kg [A] - Can 2.3 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 2.3 kg [B]

Syntech Pavicrom A 2-component coloured finish, with an epoxy resin base in aqueous dispersion. Ideal for the pigmented coating of industrial flooring and concrete products in general. Surfaces treated with Syntech Pavicrom are easy to clean and provide excellent resistance to mechanical wear, as well as having a high resistance to water, alkaline solutions, detergents and hydrocarbons (oils, diesel, petrol, etc.). For protective and decorative painting of concrete floors, reviving the colour of old resin flooring, wall plinth enamelling, and so on. Perfect for mechanical workshops, manufacturing industries, warehouses and factories generally in which special and high chemical and mechanical resistance are required. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Mix component A and component B separately, directly in their packages, in advance. When applying, combine the two components into a single container and thoroughly mix for 2 minutes using appropriate equipment (trolling motor). To prevent any errors in the mixing ratio that would result in a lack of or incomplete hardening, do not extract partial quantities from the packaging. Next, pour component B into the container of component A. Syntech Pavicrom is applied with a “short-pile” roller within 24 hours after applying the primer. Add the dilution water: the first coat diluted with water at a rate of 10 ÷ 20% depending on the porosity, cohesion of the support and the temperature; the second finish must be diluted by 6 ÷ 11%. After adding the dilution water, continue mixing for a few minute. We recommend applying two overlapping coats of the product, at temperatures not lower than +5° C. The second coat must be applied within 24 hours. 3-5% by weight of quartz B0 or B1 (or hollow glass microspheres) can also be added to achieve a non-slip effect. In two coats, apply 0.25 to 0.40 kilograms of Syntech Pavicrom per square metre of surface to be covered. Can 5 kg [A] - Can 2.5 kg [A] - Can 5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B] - Kit: 1 Can 2.5 kg [A] + 1 Can 2.5 kg [B]

Syntech Pavistrong A two-component coating with a modified epoxy resin base, specific for protecting concrete surfaces destined to be in contact with aggressive agents or for containing food products and drinking water. Syntech Pavistrong is certified according to EN 1504-2, for the protection of structures in reinforced concrete as well as for food contact, in accordance with the requirements of Ministerial Decree 21/03/73 and subsequent amendments. Syntech Pavistrong is characterized by its excellent chemical resistance to aggressive exposure environments, to alkalis even at high concentration, to medium concentration acids and to the flow of liquids even containing solid suspensions. It is impermeable to water and chemically aggressive agents. It constitutes an effective barrier to the penetration of carbon dioxide and the carbonation of concrete. It is non-toxic, therefore suitable for contact with food and drinking water. It has excellent adhesion to concrete, steel, bricks, stone in general and various materials commonly used in construction. The fluid consistency makes Syntech Pavistrong fast and easy to apply both by brush and roller. Industrial concrete floors. Purification tanks for waste water and related technical rooms. Food tanks, pipes and containers. Digesters and plants for the production of biogas. Coating of canalizations and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containers for accidental spills of petroleum products, chemicals and food products. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to first apply the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Thoroughly mix the two components in their respective containers. Pour the can of component B into the can of component A, mix thoroughly for 2-3 minutes. To obtain a perfect mixing use a mechanical stirrer or a suitable tool. The mixture of the two components must be spread within 20-30 minutes, in order to avoid hardening in the can itself. Note that the reaction rate depends on the ambient temperature (at 30 ° C it hardens in 15 minutes). Apply on the surface to be treated, in two coats, within the indicated times, for an indicative consumption of 500-600 g / m². Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Do not dilute the components or the mixture of the two components. From 0.50 to 0.60 kg of SYNTYECH PAVISTRONG for each square metre of surface to be covered, for two coat applications (0.25-0.30 kg per single coat). Can 2 kg [A] - Can 6 kg [A] - Can 1 kg [B] - Can 3 kg [B] - Kit: 1 Can 2 kg [A] + 1 Can 1 kg [B] - Kit: 1 Can 6 kg [A] + 1 Can 3 kg [B]

Syntech Primer EP-W Syntech Primer EP-W is a solvent-free two-component epoxy resin to be used as a bonding primer for applying all epoxy cycles on concrete surfaces and concrete conglomerates in general. Syntech Primer EP-W is formulated to achieve an elevated impregnation, consolidation and adhesion effect of the substrate. It can also be used on wet surfaces. Syntech Primer EP-W even penetrates deep into compact surfaces, effectively consolidating the support. It also has a great resistance to water and aggressive solutions whilst allowing water vapour to pass through. Promotes adhesion for epoxy coatings as well as for porous and deteriorated substrates, along with acting as a cement and concrete consolidation agent. The support on which the epoxy, polyurethane or methacrylic system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric expansion, vibrations etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 4%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line or grouted with Syntech AS 21. In the event of the presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply the Syntech Pavidamp epoxy resin for "wet bottoms" beforehand. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Mix the two components, each in its own container, before combining. Pour component B into component A and mix for 3 to 5 minutes with a low-speed mixing drill to achieve the complete homogenisation of the mixture. The protective coating can be applied once the Syntech Primer EP-W is completely dry. Use 150 to 200 grams per square metre per coat, depending on the porosity and unevenness of the support. Can 10 kg [A] - Can 5 kg [A] - Can 5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Syntech Epox Timber Syntech Epox Timber is a liquid, transparent, two-component epoxy resin for incorporating thick objects, mass filled casting and the treatment of wood. Its self-levelling and non-yellowing nature, along with its scratch-resistance and fluid consistency, render it ideal for pouring and for filling any voids. The final effect of Syntech Epox Timber is a smooth and even surface with a transparency similar to glass. It is also possible to colour the product with specific pigments to achieve a coloured transparent effect. It is advisable to conduct preliminary tests to achieve the desired aesthetic effect. Syntech Epox Timber can be applied in thicknesses from 0.5 to 10 cm for the creation of tables and shelves in wood and resin, artistic creations and high thickness castings in which to incorporate small parts, stones, shells and objects in general, including metal . Higher thicknesses and castings without inserting embedded objects can cause overheating during the catalysis of the product. Syntech Epox Timber has excellent chemical resistance, abrasion, scratches and wear, has a high degree of transparency that lasts over time thanks to UV filters, the self-leveling consistency and low viscosity facilitate the elimination of bubbles air and allow to obtain planar surfaces, it does not contain solvents. Excellent resistance to water, basic solutions. Fair resistance to acids and solvents. Syntech Epox Timber is a transparent vitrifying resin to be applied by pouring for the construction of tables and wood-resin surfaces, by incorporating boards, fragments or sections of wood, even irregular, appropriately treated and thick coatings on even wood surfaces. If the support is absorbent, such as untreated wood or porous materials, it must be previously treated with the same Syntech Epox Timber applied by brush to avoid the formation of air bubbles. To make bulk filler castings, prepare suitable molds of the desired shape. Make sure you have 'leveled' the surface so that the resin can level itself correctly and thus a perfectly flat surface is obtained. Mix components A (basic formulation) and B (hardener) each in their own container before mixing; then pour component B into the container of component A. Mix everything for a few minutes using a mechanical stirrer at variable speed until a homogeneous mixture is obtained, with a uniform color and free of lumps. Do not take partial quantities from the packs to avoid any errors in the mixing ratio which would cause failure or incomplete hardening. After mixing, proceed by pouring the mixture into the previously prepared mold. High thickness castings require hardening times between 48-72 hours at a temperature of 25-30 ° C. To avoid surface defects or lengthening of the hardening time, it is advisable to work in an environment with a temperature of at least 25 ° C, a temperature to be maintained throughout the hardening period. The completely hardened product can be polished like normal lacquers paying attention to the residual elasticity, during the polishing process it is necessary to avoid overheating the surface to avoid temporary softening. Otherwise, you can proceed with the application of clear acrylics after having sanded the resin with 500/1000 paper. Approximately 11 kg / m² of Syntech Epox Timber for each centimeter of thickness to be created (approximately 1100 kg for each cubic meter). PACKAGING AND DIMENSIONS: Pail 0.7 kg [A] - Pail 3.5 kg [A] - Pail 0.3 kg [B] - Pail 1.5 kg [B] - Kit: 1 Pail 0.7 kg [A] + 1 Pail 0.3 kg [B] - Kit: 1 Pail 3.5 kg [A] + 1 Pail 1.5 kg [B]

Syntech IC 55 A two-component pure epoxy adhesive that is fluid with a low viscosity, free from fillers and solvents, being specific for high performance structural consolidation injections in crumbling masonry, degraded concrete, aging screeds and industrial flooring, cracked plasters and mortars and so on. It is ideal for securing bars, clamps and tie-rods. It is also perfect for the deep consolidation of wooden materials and other types of porous materials, with impregnation by brush or roller. Reinforcing and filling injections of cracks in concrete, stone, brick, mixed works etc. Anchor, bonding and attachment of connectors, plates etc. Structural reinforcement and small volume rebuilding (only horizontal) in general. Reinforcement of porous construction materials such as wood, natural stone, bricks etc. The surfaces of application will be seasoned and dry (residual humidity measured at a depth of 4 cm, should not be greater than 4 % ), free from dust, grease, soiling, crumbling and non-adhering parts. Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A taking care to remove all the material from the packaging, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mixture is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous lump-free mixture is obtained. Lay the material using the techniques specific to the type of intervention: injection, pouring, brushing, etc.. Do not apply on wet or pulverised media. Non-conformities of the support can have unpleasant drawbacks: detachments, large bubbles, etc. Apply only in the intended thermal intervention (+8/+35 °C). Use the product immediately after mixing and mix only the amount of product intended for immediate use. Syntech IC 55 is a product based on fluid epoxy resins. It may cause variations in the colour of the product on which it is applied, both wood and stone material. For this reason it is recommended to carry out preliminary tests. Approximately 1.1 kg of SYNTECH IC55 for each cubic decimetre of volume to be filled. Can 1 kg [A] - Can 5 kg [A] - Can 0.5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 1 kg [A] + 1 Can 0.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Armaglass Grid 33 Armaglass Grid 33 is a square reinforcement gusset, with a side of 17 cm, made with glass yarn bars and pultruded epoxy resin. The monolithic, bidirectional mesh has a 33x33mm mesh, with a bar diameter of 3mm. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. Armaglass Grid 33 is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with Armaglass Structura meshes in pultruded glass for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Grid 33 is combined. Apply Armaglass Grid 33 together with the Armaglass Connectors provided in the reinforced plastering cycle, in order to guarantee greater structural collaboration between the mesh, connector and mortar of the RINFOR SYSTEM reinforcement system. Based on the connectors provided in the CRM system. Packaging: Bulk from 1 piece UM: €/piece

Syntech Acid Resistant Chemical-resistant coating based on modified epoxy phenolic resins, for the protection of walls, floors and concrete, steel and fiberglass structures. Two-component epoxy phenolic resin, applicable by spray, roller or spatula, for the coating and waterproof protection of structures subject to strong chemical aggression. Property: high mechanical and abrasion resistance, high adhesion to surfaces good elasticity high chemical resistance to acids, bases and solvents very high tenacity and ease of cleaning and maintenance high chemical resistance to petrol, fuels and hydraulic oil applicable in thick layers, even several times. Industrial floors in concrete. Waste water purification tanks and related technical rooms. Tanks, ducts and food containers. Digesters and plants for the production of biogas. Coating of pipes and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containment tanks for accidental spills of petroleum products, chemicals and food products. Protective coating of floors and walls of food, dairy, wine, breweries, distilleries, oil mills, oil mills. As a primer: 0.20 - 0.25 kg of Syntech Acid Resistant for each square meter of surface to be primed. As a coating: 0.40 kg of Syntech Acid Resistant for each square meter of surface to be coated. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Syntech Bioflex Anti-acid coating based on modified epoxy and polysulphide polymers, for the waterproof coating of concrete and steel tanks, tanks and containment tanks. High mechanical and abrasion resistance High adhesion to surfaces Good elasticity High chemical resistance to acids, bases and solvents Very high tenacity and ease of cleaning and maintenance Applicable to heavy thicknesses. Anti-acid waterproofing protective coating for the chemical industry Internal and external lining of tanks, tanks, cisterns, towers, pylons, etc. Waterproof protective coating of digesters of biogas and purification plants Anti-acid protective coating for sewers, secondary tanks, sewer collectors, channels and ducts intended for the containment of waste water and drainage Anti-acid coating of fiberglass tanks for the chemical industry. From 0.40 to 0.50 kg of Syntech Bioflex for each square meter of surface to be covered, applied in two coats. Can 6.1 kg [A] - Can 3.9 kg [B] - Kit: 1 Can 6.1 kg [A] + 1 Can 3.9 kg [B]

Syntech AS 31 The two-component structural epoxy adhesive putty is soft, thixotropic and spatulable (malleable paste), ideal for anchoring steel connectors, hermetically sealing through-holes in concrete, bonding steel plates on concrete surfaces, as an accessory product for laying road joints, for the reconstruction of wooden beam heads, repairing cracks and reconstructing missing geometries, fixing injectors, reconstructing joints in concrete flooring and fixing Elastotex 250 Combi elastic strips, including when in contact with water destined for human consumption. Structural reinforcements of structural elements (beams, pillars, etc.) by bonding steel sheets to the concrete. Reconstruction of joints in concrete floorings. Rigid structural bonding (beton plaque) of prefabricated elements and of articles in different building materials: concrete, steel, glass, wood, marble, tiles, stones etc. Anchoring, bonding and attachment of connectors, ties etc. Attachment of elastic straps for waterproofing joints, Elastotex. Reconstruction of wooden heads, crack repair, reconstruction of missing geometries on various supports. The application surfaces must be suitably prepared and adequately resistant: free from dust, grease, soiling, crumbling and non-adhering parts, devoid of wet surface areas. For floorings, moreover, a shot peening or preliminary milling of the surfaces of adhesion is recommended. The metal elements are to be blasted to "almost white metal". Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A, taking care to remove all the material from the packaging and mixing thoroughly with a mixer at a low number of revolutions (or a suitable manual tool), until a homogeneous mixture is obtained, indicated by the uniform colour and the absence of lumps. Apply to the surfaces with the help of spatulas, trowels, etc. Complete the tasks during the useful life of the product. Do not apply in rainy days; do not apply on moist or wet supports; do not apply on pulverised supports; use the product immediately after mixing. Approximately 1.6 kg of Syntech AS 31 for each cubic decimetre of volume to be grouted. Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 0.5 kg [B]

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Syntech Pavicar Two-component coating based on epoxy and polyurethane resins; for the coating, waterproofing and elastic protection of roofs, terraces, pavements, stairs, car parks and surfaces that are cracked or subject to micro-cracks and crazing. High wear resistance Applicable on tarred surfaces and bituminous sheaths Walkable product suitable for covering and waterproofing flat roofs Ease and speed of application with quick intervention times Soft and velvety to the touch Elastic product resistant to dynamic stress Available in two colors. Waterproof coating of concrete, ceramic, porcelain stoneware, wood, sheet metal supports, tarred supports and bituminous sheaths, suitably primed. Creation of elastic and waterproof protections for multi-level parking areas, both internal and external. Ideal for waterproofing cycles of balconies, roofs and terraces as it does not require preliminary demolition work or replacement of coverings. Its application allows the creation of a continuous, elastic and waterproof layer resistant to wear and trampling. Approximately 2.0 kg of Syntech Pavicar for each square meter of surface to be covered, in two coats. Can 8.3 kg [A] - Can 16.7 kg [A] - Can 4.17 kg [A] - Can 1.7 kg [B] - Can 3.3 kg [B] - Can 0.83 kg [B] - Kit: 1 Can 4.17 kg [A] + 1 Can 0.83 kg [B] - Kit: 1 Can 8.3 kg [A] + 1 Can 1.7 kg [B] - Kit: 1 Can 16.7 kg [A] + 1 Can 3.3 kg [B]

Armaglass Corner 33 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh with a side of 33 mm, an ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 33 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 33 is combined. Apply Armaglass Corner 33 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Packaging: Loose from 1.05 meters UM: €/piece

Armaglass Corner 99 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh with a side of 99 mm, an ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 99 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 99 is combined. Apply Armaglass Corner 99 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Based on the total length of the corner areas. Packaging: Loose from 1.05 meters UM: €/piece

Armaglass Corner 66 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh of 66 mm side, ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 66 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 66 is combined. Apply Armaglass Corner 66 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Based on the total length of the corner areas. Packaging: Loose from 1.05 meters UM: €/piece

Viscosité moyenne et temps d'utilisation long. Bonne résistance à l'abrasion et à la compression. -> Application Modèle de fonderie. Matrices et poincons d'emboutissage. Modèles de copiage / reproduction. Mère de moule. Calage de machine. Couleur : Noir Ratio mélange : 100/10 Potlife : 100 min Temps avant démoulage : >24h TG°C : 74 Unité de vente : 1,65kg Minimum de commande : 1 kit