Produse pentru mingoda (125)

Ball lock pins are used for easy fastening or joining of components or workpieces. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. Release the button to lock the balls and secure the connection. If required, the ball lock pins can be fitted with a retaining cable. The hardened, high-tensile stainless steel pin permits extreme loads with low wear. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Reference:03196

Ideal elements for fastening cladding panels, Plexiglas covers etc. The oversized flange and the thread undercut ensure a stress-free, uniform force distribution on the respective surfaces. Projecting edges are kept to a minimum by the head height being kept as low as possible. An open-end spanner is used to screw the fastener in. The surface of the ball head screw is polished and, with regard to design optimised for the use in hygienic environments. The surface is polished to a surface finish of less than Ra 0.8 µm. Dirt and residue from products or cleaners seldom adheres and easy cleaning is ensured. Reference:07175-02 Material:Stainless steel 1.4404 Version:Polished

Formes C et F : Bille acier, corps en acier de traitement. Formes G et J : Bille acier de traitement, corps en acier. Finition : Formes C et F : Bille trempée et bruni, corps phosphatée. Formes G et J : Bille phosphatée, corps trempée et bruni. Nota : Les supports à bille oscillante servent d‘éléments de serrage, d’appuis et d’éléments de pression dans la construction de gabarits et montages. Après libération de la force d'appui, la surface d’appui se repositionne dans la position initiale. Bille avec protection anti-retournement. Référence:02081 Forme C:avec filetage, bille avec plat, lisse Forme F:avec filetage, bille avec plat, strié Forme G:avec support taraudé, bille avec plat, lisse Forme J:avec support taraudé, bille avec plat, strié

Housing, grey cast iron. Bearing, ballbearing steel 100Cr6. Seal, rubber NBR. Pillow block bearings consist of a sealed singlerow ball bearing with a spherical outer ring which is mounted in a housing. Because of the spherical outer surface of the bearing, shaft misalignment can be compensated for. The bearings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by grub screws on the inner ring. In normal applications, pillow block bearings are maintenancefree due to the lifetime lubrication. In difficult environmental conditions relubrication can be carried out over the grease nipple. All housing dimensions are nominal dimensions for which the usual casting tolerances must be taken into consideration. Reference:24200 Version:Housing, painted Temperature range:-15 °C to +100 °C

Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note By telescopic slides with full extension, the travel is roughly equal to the installed length, which ensures greater comfort and accessibility. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 80,000 cycles. Not suitable for horizontal mounting. The head height of the fastening screws should not exceed 1.8 mm otherwise there is a risk of collision with other parts of the slide. Advantages Low slide thickness Light running Precise guidance for high lateral stability Reference:21334