Produse pentru epoxidharz (48)

ALWA EPF 10 is a temperature-resistant, steel-filled gelcoat based on epoxy resin. It is used to produce temperature and abrasion resistant surfaces for vacuum, PU foam, thermionic moulds and heating plates, among others.

Syntech Pavisheer A two-component epoxy system based on epoxy resins in aqueous dispersion and solvent-free. It is ideal for completing protective, transparent treatments with a consolidating action and anti-dust effect on industrial concrete flooring, with good mechanical and chemical resistance, especially in reference to contact with oils and solvents. This product also serves well as a primer for casting joints between old and new concrete flooring. Transparent finish of interior floor coverings, mechanical-resistant impregnations, anti-dust and anti-oil for concrete surfaces. The media should have adequate mechanical resistance. The concrete surfaces should be cured, dry, planar and absorbent, free from oils, detergents, powders and soiling. The most appropriate type of mechanical preparation should also be determined (degreasing or shot peening). Conveniently absorbent surfaces may be dealt with directly after a proper cleaning. For tiled surfaces and for pre-existing coverings in resin, a degreasing or shot peening treatment is required until complete opacification and complete elimination of dust. Mix components A and B each in their own container before mixing. Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Pour component B into a suitable container and add component A. Mix everything for a few minutes using a mechanical stirrer with variable speed until a homogeneous and uniform color mixture is obtained. Leave to rest for a few minutes and mix again. Dilute the final product only with water in the Syntech Pavisheer: water ratio of 1: 3 for the first coat and 1: 2 for the second. Gradually add the dilution water, continuing to mix for a few minutes. The dilution ratio can vary according to the porosity of the support; if necessary on closed surfaces it is also possible to dilute the second coat respecting the dilution ratio 1: 3. The Syntech Pavisheer emulsion has a stability of about 2 hours at 20 ° C; within this period the product must be used. Syntech Pavisheer is applied with a short-haired roller or spray, covering the entire surface evenly. We recommend application at temperatures not lower than 5 ° C. From 0.10 to 0.15 kg of SYNTYECH PAVISHEER for each square metre of surface to be covered. Can 5 kg [A] - Canister 1 kg [A] - Can 5 kg [B] - Canister 1 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 1 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B]

solidian REMATs werden aus unseren korrosionsbeständigen und extrem festen solidian REBARs hergestellt. Die Bewehrungsstäbe sind durch dauerhafte und solide spritzgegossene Kreuzungspunkte miteinander verbunden und bilden die starre Matte. Damit verbinden solidian REMATs die gleichen unglaublichen mechanischen Eigenschaften unserer solidian REBARs mit dem effizienten Handling einer robusten Matte auf der Baustelle. Sie müssen Ihre Bewehrungsstäbe nicht mehr in Ihrem Fertigteilwerk oder auf der Baustelle zusammenknoten und sparen so Zeit und Geld. Die soliden Knotenpunkte ermöglichen es, dass Sie die solidian REMATs begehen können. Was spricht also dafür, weiterhin Stahl oder Edelstahl zu verwenden?

SOLVENT PAINT of COSMOCHROME is a high quality undercoat for concrete surfaces (concrete columns, concrete floors, walls, ceramic tile roofs etc). It is highly durable against extreme weather conditions and atmosphere pollution. It has strong adhesion, great covering power and extreme hardness PACKAGE:0,75 LT, 10 LT, 2,5 LT COLOR:Black, Cypress Green

It is a material with a high resistance to chemicals. Its specific weight is low. It is a slippery material with a low coefficient of friction. The water and moisture absorption property is close to zero. It can be used as cutting plate especially in industrial kitchens and butcher cutting log. It has the ability to be welded. The element that characterizes polyethylene is the molecular weight. Low molecular weight can be grouped into three groups: low molecular weight (PE 300), high molecular weight (PE 500) and ultra high molecular weight (PE 1000).

Epoxy Resin Top Wooden Iron Trolley Design - Dining F & B & Kitchen Trolleys SKU:SS3601 Dimensions:67 × 104 × 101 cm

NTC temperature sensors coated with epoxy resin have a very low temperature tolerance classification and a wide measuring range of -40…+150 °C. Name:NTC temperature sensor Sensor:NTC Temperature measuring range:-40...+150 °C Nominal resistance:1 kΩ Resistance tolerance:±1% Response time temperature:1 s in liquids Housing:Epoxy resin coated Beta constant:3348 K ±1.0% Self heating:0.85 mW/K Connection wires:Ø 0.5 x 65 mm, 10 mm uninsulated, silver-plated copper with white Teflon® insulated Dimensions:Ø2.5 x 69 mm Producer:Measurement Specialties, Inc. Producer article number:1K2A1B Weight:0.0014 kg

The STRATE AWALIFT 1/2x2 is used in many applications that require small quantities of waste water to overcome a high discharge head. With a capacity of 15 m3/h, the system is suitable for up to 750 EW. The system can be adapted to your individual needs through the use of different motor variations. Drainage of small towns with up to about 750 residents that cannot be drained using natural gradient. Drainage with larger pumping heads and longer pressure pipes As an intermediate pumping station within a pressure drainage system Residential and industrial areas Towns Communities Infrastructure facilities such as airports, industrial parks, underground stations etc. Product features The tank with two separator systems Four centrifugal pumps ST (M)65/80, motors according to type and operating location required Four pump gate valves One Y-pipe Two STRATE non-return valves Two gate valves Level measurement LGA certified according to DIN EN 12050-1 /. -4 Tank:S235JR (St37-2) Coating:2 component coating on epoxy resin basis

Hier vervollständigen wir Informationen zur Anwendung und anderen Funktionen. Haltbarkeit, ästhetisches Erscheinungsbild und einfache Reinigung machen diese Produkte zu einem bevorzugten Produkt für Bodenbeläge in öffentlichen, industriellen und gewerblichen Gebäuden, Garagen usw. Paletten sind Mehrwegverpackungen. Es ist möglich, andere Fliesenmuster anzufertigen in Absprache mit dem Kunden. Für den Transport werden die Fliesen vereinzelt auf Paletten gelegt aus Styropor und mit Schrumpffolie überzogen. Eine Palette enthält 19,44 m2 Fliesen Abmessungen der Fliesen:30x30x2.8 Gewicht der Fliesen:68 kg Abmessungen des Sockels:30x7.3x1.2 cm Sockelgewicht:2 kg

EPOXID GIESSHARZE FÜR INDUSTRIE UND ELEKTRONIK Epoxidharze sind Kunststoffe von hoher Festigkeit und chemischer Beständigkeit. Sie sind härter und weniger dehnbar als Polyurethane, haben eine höhere Bruchspannung und besonders auf Metallen eine höhere Klebekraft. AUF EINEN BLICK: *Härter als Polyurethane *Höhere Bruchspannung *Geringere Dehnbarkeit *Höhere Klebkraft auf Metallen *Bessere chemische Beständigkeit gegen Lösungsmittel

Unser 2k-Epoxidharzmörtel mit Novolak-Harz ist 8 mal härter als Beton. In 9 verschiedenen Farben und den Versionen Original, Rapid, Kalttrocknend, Säureresistent und Unter Null erhältlich.

Sicherheitsschalter mit integrierter Auswerteelektronik • Mit Epoxidharz umgossener Sicherheitsschalter CES-C04 • Geprüft auf Materialbeständigkeit entsprechend Ecolab-Vorgabe • 2 Sicherheitsausgänge (Halbleiterausgänge) • Kategorie 4 / PL e nach EN ISO 13849-1 • Drei aktive Flächen • Anschlussleitung PUR, 20 m, mit Aderendhülsen • Multicode • Meldeausgang OD Bemessungsisolationsspannung Ui: 300 V Bemessungsstoßspannungsfestigkeit Uimp: 1,5 kV Schaltfrequenz: max. 1 Hz Schock- und Schwingfestigkeit: gemäß EN 60947-5-3 Schutzart: IP65/IP67/IP69/IP69K

Que cela soit une table toute simple ou une table de réunion nous pouvons réaliser votre projet sur mesure ! En bois massif ou en version Hybride (table rivière) en Bois et résine époxy; il vous suffit de nous contacter pour étudier votre projet.

Bougeoir lotus en résine époxy et bougie cœur ~ Bougeoir en résine époxy de la collection blanc et or, en forme de lotus, fourni avec une petite bougie cœur avec fragrance vanille en cire de soja 100% naturelle. Taille du bougeoir : 4 cm de haut / 8cm de diamètre. Toutes les créations sont réalisées à la main dans mon atelier ! N'hésitez pas à me contacter via le formulaire de contact ou les réseaux pour toute demande de personnalisation ~

Filling compound such as epoxy resin filler (“epoxy putty”), fine filler or repair putty are used for corrosion protection, repairing scratches and unevenness in metal, wood and fibreglass-reinforced plastics. These coatings are mainly used in boat building.

SE8400 Type 30™ singleend roving is specifically designed for pultrusion processing in applications requiring high electrical resistance. Produced with Advantex®, corrosionresistant ECR glass technology by Owens Corning. Compatible with polyester, vinyl ester and epoxy resins. EFFICIENT PROCESSING Better wetout in polyester, vinyl ester, and epoxy resin, offering fast processing and good glasstoresin bonding, resulting in optimized part production. Good wetout and resin bonding results in excellent visual appearance of parts produced. GOOD MECHANICAL PROPERTIES Low seed glass results in excellent dielectric properties which are ideal for applications requiring high electrical resistance. ADVANCED SERVICE LIFE Advantex® corrosion resistant glass fiber combined with low seed glass is ideal for longterm electrical, physical, and acid resistance, reducing the potential for costly brittle fracture failures in the field. STRAND TENSILES: ASTM D 2343:Tensile Strength, psi (Mpa) AVG. E-701 POLYESTER RESIN:353,900 (2440) % GLASS :58.8 AVG. DER 331 EPOXY RESIN:338,800 (2336) % GLASS:54.5 TEX:4400 YIELD:113 MANUFACTURING REGION:North America

Auch für Harzmatten und Reaktionsmassen eignet sich das System. ALWA HT RESIN ist besonders interessant für die Raumfahrt- und Flugzeugindustrie sowie den Schienenverkehr, Automobil- und Elektroindustrie. Die Einsatzgebiete von Epic-Harzen sind u. a. Elektroverguss, Laminier- und Injektionstechnik (RTM Verfahren), Vakuuminfusion, Gieß- oder Stampfmassen, Imprägnierharz, Gieß- und Spritzgussverfahren sowie Pregpreg- Technologien. ALWA HT RESIN wird in zwei Ausführungen angeboten. ALWA HT RESIN M100 mit ca. 50 mPa s ALWA HT RESIN M2200 mit ca. 2200 mPa s ALWA HT RESIN zeichnet sich durch gute elektrische Isolationseigenschaften aus. Darüber hinaus sind die mechanischen und elektrischen Eigenschaften nahezu temperaturunabhängig. Zudem besteht eine gute chemische Beständigkeit gegenüber Säuren, Laugen und organischen Lösungsmitteln. Quarzmehl, Microdol, Kurzglasfasern, Graphit, Quarzsand, Korund und Aluminiumpulver können mit ALWA HT RESIN verarbeitet werden.

ALWA EPT 210 is a laminate and backfilling resin. Laminates can be produced with ALWA EPT 210 in order to manufacture glass fibre plastic parts, gauges, templates, moulds and applications with diverse fillers. ALWA EPT 210 is an epoxy resin that has a low viscosity and a light yellow colour. Under exothermic reaction, it cures in connection with the light yellow hardener H 10 at room temperature. The mixture shows a low viscosity and is particularly appropriate for laminating layers of up to 8 mm. For thicker laminates the application of layers must be interrupted several times in order to avoid too high reaction temperatures in the laminate.

Syntech Pavicrom SBV Colored two-component finish, permeable to water vapour, based on epoxy resins in water dispersion. Ideal for the pigmented coating of industrial floors and concrete constructions in general with residual humidity and without vapor barrier. Surfaces treated with Syntech Pavicrom SBV are easy to clean and guarantee excellent resistance to mechanical wear, as well as being highly resistant to water, alkaline solutions, detergents and hydrocarbons (petroleum, diesel, petrol, etc.) . Protective and decorative painting of concrete floors, restoration of the color of old resin floors, glazing of wall skirting boards, etc. Ideal for mechanical workshops, manufacturing industries, warehouses and factories in general where high chemical and mechanical resistance is required. It can be used both indoors and outdoors. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating. In case of restoration, use suitable mortars and products suitable for the system beforehand. Wait for the drying times before applying the next coat. The tensile strength must not be less than 1.5 N/mm². Existing paints, coatings or paints, cement grout residues, release agents, oils, greases, silicones, etc. they can be removed mechanically by sandblasting, blasting, hydroblasting or chemical removal. Cracks and fissures In case of static cracks, use Syntech Primer EP-W for sealing. The sealing of dynamic cracks or cracks larger than 4-5 mm must be assessed on site. Generally they can be grouted with elastomeric materials or act as expansion joints. Grouting and spot repairs Any holes or repairs to portions of concrete can be made with mortars from the REPAR line or by applying epoxy mortar made with Syntech Primer EP-W and quartz mastics. Apply a coat of Syntech Primer EP-W as a bonding primer, then proceed to seal and repair the damaged and broken concrete by applying the epoxy mortar. Any small filling of holes and cracks can be done by applying Syntech AS 21 epoxy mortar. Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Primer for concrete Syntech Pavicrom SBV can be applied directly to cementitious substrates as the product diluted with a maximum of 25% by weight of clean water acts as an anchoring primer. Resin coatings The application of Syntech Pavicrom SBV on resinous and multilayer systems must always be preceded by sanding the entire surface to promote and guarantee optimal adhesion of the product to the support. Combine the two components in the indicated mixing ratio. Add component B (hardener) to component A (base) and mix well until a completely homogeneous product is obtained. It is advisable to start mixing briefly with an electric drill at low speed and then intensify the stirring up to a maximum of 300-400 rpm. Leave the emulsion obtained to rest in the container, respecting the following induction times: at 15°C ~ 20 minutes at 25°C ~ 15 minutes at 30°C ~ 10 minutes The product can be applied uniformly using a spray gun or short-haired roller to avoid accumulations of material which could give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area to obtain a uniform film and eliminate any accumulations of product. Apply the first coat of Syntech Pavicrom SBV diluted with a maximum of 25% by weight of clean water as primer. The dilution must be carried out under mechanical stirring, adding the necessary quantity of water at the end of the induction time. Do not dilute the product further during application if it thickens it means that the use time has expired. Create a new emulsion with highly mixed material. Wait at least 12 hours, then apply the second one Colored finish diluted with a maximum of 20% weight of clean water, respecting the consumption and thicknesses indicated. It is possible to create non-slip finishes by adding quartz or hollow glass spheres. From 0.15 to 0.20 kg of Syntech Pavicrom SBV for each square meter of surface to be covered, for each coat. Pail 2.5 kg [A] - Pail 5 kg [A] - Pail 3 kg [B] - Pail 6 kg [B] - Kit: 1 Pail 2.5 kg [A] + 1 Pail 3 kg [B] - Kit: 1 Pail 5 kg [A] + 1 Pail 6 kg [B]

Syntech Epox Level Two-component coloured, high solids, self-levelling and/or multi-layer epoxy coating on concrete surfaces and cementitious substrates. Excellent mechanical and abrasion resistance Wide range of colors available Uniform, glossy finish with possible non-slip finish Excellent mechanical and chemical resistance Excellent resistance to detergents and disinfectants. ▪ Colored abrasion resistant coating ▪ Coating of floors subjected to intense traffic ▪ Coating of floors in laboratories, hospitals, sterile rooms and aseptic rooms ▪ Flooring of warehouses, shopping centres, museums, showrooms, storage and logistics areas ▪ Coating of floors of underground car parks, garages, hangars, automotive and aeronautical industries ▪ Coating of food industry floors ▪ Coating of floors in chemical and pharmaceutical industries. Self-leveling coating SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 Multilayer system 1st layer SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 + 2-3 kg/m2 for waste sowing 2nd layer SYNTECH EPOX LEVEL: 0.5 kg/m2 QUARTZ 0.1-0.5: 0.2 kg/m2 + 2-3 kg/m2 for waste sowing Finish SYNTECH EPOX LEVEL: 0.3 kg/m2 QUARTZ 0.06-0.25: 0.05 kg/m2. Can 10 kg [A] - Can 2.3 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 2.3 kg [B]

Syntech Pavicrom A 2-component coloured finish, with an epoxy resin base in aqueous dispersion. Ideal for the pigmented coating of industrial flooring and concrete products in general. Surfaces treated with Syntech Pavicrom are easy to clean and provide excellent resistance to mechanical wear, as well as having a high resistance to water, alkaline solutions, detergents and hydrocarbons (oils, diesel, petrol, etc.). For protective and decorative painting of concrete floors, reviving the colour of old resin flooring, wall plinth enamelling, and so on. Perfect for mechanical workshops, manufacturing industries, warehouses and factories generally in which special and high chemical and mechanical resistance are required. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Mix component A and component B separately, directly in their packages, in advance. When applying, combine the two components into a single container and thoroughly mix for 2 minutes using appropriate equipment (trolling motor). To prevent any errors in the mixing ratio that would result in a lack of or incomplete hardening, do not extract partial quantities from the packaging. Next, pour component B into the container of component A. Syntech Pavicrom is applied with a “short-pile” roller within 24 hours after applying the primer. Add the dilution water: the first coat diluted with water at a rate of 10 ÷ 20% depending on the porosity, cohesion of the support and the temperature; the second finish must be diluted by 6 ÷ 11%. After adding the dilution water, continue mixing for a few minute. We recommend applying two overlapping coats of the product, at temperatures not lower than +5° C. The second coat must be applied within 24 hours. 3-5% by weight of quartz B0 or B1 (or hollow glass microspheres) can also be added to achieve a non-slip effect. In two coats, apply 0.25 to 0.40 kilograms of Syntech Pavicrom per square metre of surface to be covered. Can 5 kg [A] - Can 2.5 kg [A] - Can 5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B] - Kit: 1 Can 2.5 kg [A] + 1 Can 2.5 kg [B]

Syntech Pavistrong A two-component coating with a modified epoxy resin base, specific for protecting concrete surfaces destined to be in contact with aggressive agents or for containing food products and drinking water. Syntech Pavistrong is certified according to EN 1504-2, for the protection of structures in reinforced concrete as well as for food contact, in accordance with the requirements of Ministerial Decree 21/03/73 and subsequent amendments. Syntech Pavistrong is characterized by its excellent chemical resistance to aggressive exposure environments, to alkalis even at high concentration, to medium concentration acids and to the flow of liquids even containing solid suspensions. It is impermeable to water and chemically aggressive agents. It constitutes an effective barrier to the penetration of carbon dioxide and the carbonation of concrete. It is non-toxic, therefore suitable for contact with food and drinking water. It has excellent adhesion to concrete, steel, bricks, stone in general and various materials commonly used in construction. The fluid consistency makes Syntech Pavistrong fast and easy to apply both by brush and roller. Industrial concrete floors. Purification tanks for waste water and related technical rooms. Food tanks, pipes and containers. Digesters and plants for the production of biogas. Coating of canalizations and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containers for accidental spills of petroleum products, chemicals and food products. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to first apply the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Thoroughly mix the two components in their respective containers. Pour the can of component B into the can of component A, mix thoroughly for 2-3 minutes. To obtain a perfect mixing use a mechanical stirrer or a suitable tool. The mixture of the two components must be spread within 20-30 minutes, in order to avoid hardening in the can itself. Note that the reaction rate depends on the ambient temperature (at 30 ° C it hardens in 15 minutes). Apply on the surface to be treated, in two coats, within the indicated times, for an indicative consumption of 500-600 g / m². Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Do not dilute the components or the mixture of the two components. From 0.50 to 0.60 kg of SYNTYECH PAVISTRONG for each square metre of surface to be covered, for two coat applications (0.25-0.30 kg per single coat). Can 2 kg [A] - Can 6 kg [A] - Can 1 kg [B] - Can 3 kg [B] - Kit: 1 Can 2 kg [A] + 1 Can 1 kg [B] - Kit: 1 Can 6 kg [A] + 1 Can 3 kg [B]

Syntech Primer EP-W Syntech Primer EP-W is a solvent-free two-component epoxy resin to be used as a bonding primer for applying all epoxy cycles on concrete surfaces and concrete conglomerates in general. Syntech Primer EP-W is formulated to achieve an elevated impregnation, consolidation and adhesion effect of the substrate. It can also be used on wet surfaces. Syntech Primer EP-W even penetrates deep into compact surfaces, effectively consolidating the support. It also has a great resistance to water and aggressive solutions whilst allowing water vapour to pass through. Promotes adhesion for epoxy coatings as well as for porous and deteriorated substrates, along with acting as a cement and concrete consolidation agent. The support on which the epoxy, polyurethane or methacrylic system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric expansion, vibrations etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 4%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line or grouted with Syntech AS 21. In the event of the presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply the Syntech Pavidamp epoxy resin for "wet bottoms" beforehand. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Mix the two components, each in its own container, before combining. Pour component B into component A and mix for 3 to 5 minutes with a low-speed mixing drill to achieve the complete homogenisation of the mixture. The protective coating can be applied once the Syntech Primer EP-W is completely dry. Use 150 to 200 grams per square metre per coat, depending on the porosity and unevenness of the support. Can 10 kg [A] - Can 5 kg [A] - Can 5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Syntech Epox Timber Syntech Epox Timber is a liquid, transparent, two-component epoxy resin for incorporating thick objects, mass filled casting and the treatment of wood. Its self-levelling and non-yellowing nature, along with its scratch-resistance and fluid consistency, render it ideal for pouring and for filling any voids. The final effect of Syntech Epox Timber is a smooth and even surface with a transparency similar to glass. It is also possible to colour the product with specific pigments to achieve a coloured transparent effect. It is advisable to conduct preliminary tests to achieve the desired aesthetic effect. Syntech Epox Timber can be applied in thicknesses from 0.5 to 10 cm for the creation of tables and shelves in wood and resin, artistic creations and high thickness castings in which to incorporate small parts, stones, shells and objects in general, including metal . Higher thicknesses and castings without inserting embedded objects can cause overheating during the catalysis of the product. Syntech Epox Timber has excellent chemical resistance, abrasion, scratches and wear, has a high degree of transparency that lasts over time thanks to UV filters, the self-leveling consistency and low viscosity facilitate the elimination of bubbles air and allow to obtain planar surfaces, it does not contain solvents. Excellent resistance to water, basic solutions. Fair resistance to acids and solvents. Syntech Epox Timber is a transparent vitrifying resin to be applied by pouring for the construction of tables and wood-resin surfaces, by incorporating boards, fragments or sections of wood, even irregular, appropriately treated and thick coatings on even wood surfaces. If the support is absorbent, such as untreated wood or porous materials, it must be previously treated with the same Syntech Epox Timber applied by brush to avoid the formation of air bubbles. To make bulk filler castings, prepare suitable molds of the desired shape. Make sure you have 'leveled' the surface so that the resin can level itself correctly and thus a perfectly flat surface is obtained. Mix components A (basic formulation) and B (hardener) each in their own container before mixing; then pour component B into the container of component A. Mix everything for a few minutes using a mechanical stirrer at variable speed until a homogeneous mixture is obtained, with a uniform color and free of lumps. Do not take partial quantities from the packs to avoid any errors in the mixing ratio which would cause failure or incomplete hardening. After mixing, proceed by pouring the mixture into the previously prepared mold. High thickness castings require hardening times between 48-72 hours at a temperature of 25-30 ° C. To avoid surface defects or lengthening of the hardening time, it is advisable to work in an environment with a temperature of at least 25 ° C, a temperature to be maintained throughout the hardening period. The completely hardened product can be polished like normal lacquers paying attention to the residual elasticity, during the polishing process it is necessary to avoid overheating the surface to avoid temporary softening. Otherwise, you can proceed with the application of clear acrylics after having sanded the resin with 500/1000 paper. Approximately 11 kg / m² of Syntech Epox Timber for each centimeter of thickness to be created (approximately 1100 kg for each cubic meter). PACKAGING AND DIMENSIONS: Pail 0.7 kg [A] - Pail 3.5 kg [A] - Pail 0.3 kg [B] - Pail 1.5 kg [B] - Kit: 1 Pail 0.7 kg [A] + 1 Pail 0.3 kg [B] - Kit: 1 Pail 3.5 kg [A] + 1 Pail 1.5 kg [B]

ALWA HT RESIN is a resin-based on isocyanate and epoxy (EP), which reacts after adding a catalyst. ALWA HT RESIN offers a range of possibilities for producers of fibre-reinforced materials (e.g., glass fibre, kevlar and carbon), semi-finished and finished goods. The system is also suitable for prepreg and reaction compounds. ALWA HT RESIN is particularly interesting for the aerospace and aircraft industry as well for the rail transport, automotive and electronics industry. The application area of epic resins are electro casting resins, lamination and injection technology (RTM procedure), vacuum infusion, casting and ramming compounds, impregnation resin, casting and injection moulding process as well as prepreg technologies, among others. ALWA HT RESIN is offered in two versions. *ALWA HT RESIN M100 with approx. 50 mPa s *ALWA HT RESIN M2200 with approx. 2200 mPa s The resins can be mixed with one another which enables a flexible adjustment of the viscosity.

Wir bieten Ihnen die Möglichkeit, Formbewehrungen aller Art zu realisieren. Egal ob Fassadenplatten, Betonmöbel, L-Winkel oder runde Profile – basierend auf den bewährten solidian GRID- und solidian FLEX GRID-Bewehrungen erstellen wir eine Bewehrungsform gemäß Ihren Designspezifikationen.

Syntech IC 55 A two-component pure epoxy adhesive that is fluid with a low viscosity, free from fillers and solvents, being specific for high performance structural consolidation injections in crumbling masonry, degraded concrete, aging screeds and industrial flooring, cracked plasters and mortars and so on. It is ideal for securing bars, clamps and tie-rods. It is also perfect for the deep consolidation of wooden materials and other types of porous materials, with impregnation by brush or roller. Reinforcing and filling injections of cracks in concrete, stone, brick, mixed works etc. Anchor, bonding and attachment of connectors, plates etc. Structural reinforcement and small volume rebuilding (only horizontal) in general. Reinforcement of porous construction materials such as wood, natural stone, bricks etc. The surfaces of application will be seasoned and dry (residual humidity measured at a depth of 4 cm, should not be greater than 4 % ), free from dust, grease, soiling, crumbling and non-adhering parts. Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A taking care to remove all the material from the packaging, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mixture is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous lump-free mixture is obtained. Lay the material using the techniques specific to the type of intervention: injection, pouring, brushing, etc.. Do not apply on wet or pulverised media. Non-conformities of the support can have unpleasant drawbacks: detachments, large bubbles, etc. Apply only in the intended thermal intervention (+8/+35 °C). Use the product immediately after mixing and mix only the amount of product intended for immediate use. Syntech IC 55 is a product based on fluid epoxy resins. It may cause variations in the colour of the product on which it is applied, both wood and stone material. For this reason it is recommended to carry out preliminary tests. Approximately 1.1 kg of SYNTECH IC55 for each cubic decimetre of volume to be filled. Can 1 kg [A] - Can 5 kg [A] - Can 0.5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 1 kg [A] + 1 Can 0.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Armaglass Grid 33 Armaglass Grid 33 is a square reinforcement gusset, with a side of 17 cm, made with glass yarn bars and pultruded epoxy resin. The monolithic, bidirectional mesh has a 33x33mm mesh, with a bar diameter of 3mm. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. Armaglass Grid 33 is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with Armaglass Structura meshes in pultruded glass for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Grid 33 is combined. Apply Armaglass Grid 33 together with the Armaglass Connectors provided in the reinforced plastering cycle, in order to guarantee greater structural collaboration between the mesh, connector and mortar of the RINFOR SYSTEM reinforcement system. Based on the connectors provided in the CRM system. Packaging: Bulk from 1 piece UM: €/piece

Syntech Acid Resistant Chemical-resistant coating based on modified epoxy phenolic resins, for the protection of walls, floors and concrete, steel and fiberglass structures. Two-component epoxy phenolic resin, applicable by spray, roller or spatula, for the coating and waterproof protection of structures subject to strong chemical aggression. Property: high mechanical and abrasion resistance, high adhesion to surfaces good elasticity high chemical resistance to acids, bases and solvents very high tenacity and ease of cleaning and maintenance high chemical resistance to petrol, fuels and hydraulic oil applicable in thick layers, even several times. Industrial floors in concrete. Waste water purification tanks and related technical rooms. Tanks, ducts and food containers. Digesters and plants for the production of biogas. Coating of pipes and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containment tanks for accidental spills of petroleum products, chemicals and food products. Protective coating of floors and walls of food, dairy, wine, breweries, distilleries, oil mills, oil mills. As a primer: 0.20 - 0.25 kg of Syntech Acid Resistant for each square meter of surface to be primed. As a coating: 0.40 kg of Syntech Acid Resistant for each square meter of surface to be coated. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Syntech Bioflex Anti-acid coating based on modified epoxy and polysulphide polymers, for the waterproof coating of concrete and steel tanks, tanks and containment tanks. High mechanical and abrasion resistance High adhesion to surfaces Good elasticity High chemical resistance to acids, bases and solvents Very high tenacity and ease of cleaning and maintenance Applicable to heavy thicknesses. Anti-acid waterproofing protective coating for the chemical industry Internal and external lining of tanks, tanks, cisterns, towers, pylons, etc. Waterproof protective coating of digesters of biogas and purification plants Anti-acid protective coating for sewers, secondary tanks, sewer collectors, channels and ducts intended for the containment of waste water and drainage Anti-acid coating of fiberglass tanks for the chemical industry. From 0.40 to 0.50 kg of Syntech Bioflex for each square meter of surface to be covered, applied in two coats. Can 6.1 kg [A] - Can 3.9 kg [B] - Kit: 1 Can 6.1 kg [A] + 1 Can 3.9 kg [B]