Produse pentru epoxidharz (72)

Syntech Pavicrom A 2-component coloured finish, with an epoxy resin base in aqueous dispersion. Ideal for the pigmented coating of industrial flooring and concrete products in general. Surfaces treated with Syntech Pavicrom are easy to clean and provide excellent resistance to mechanical wear, as well as having a high resistance to water, alkaline solutions, detergents and hydrocarbons (oils, diesel, petrol, etc.). For protective and decorative painting of concrete floors, reviving the colour of old resin flooring, wall plinth enamelling, and so on. Perfect for mechanical workshops, manufacturing industries, warehouses and factories generally in which special and high chemical and mechanical resistance are required. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Mix component A and component B separately, directly in their packages, in advance. When applying, combine the two components into a single container and thoroughly mix for 2 minutes using appropriate equipment (trolling motor). To prevent any errors in the mixing ratio that would result in a lack of or incomplete hardening, do not extract partial quantities from the packaging. Next, pour component B into the container of component A. Syntech Pavicrom is applied with a “short-pile” roller within 24 hours after applying the primer. Add the dilution water: the first coat diluted with water at a rate of 10 ÷ 20% depending on the porosity, cohesion of the support and the temperature; the second finish must be diluted by 6 ÷ 11%. After adding the dilution water, continue mixing for a few minute. We recommend applying two overlapping coats of the product, at temperatures not lower than +5° C. The second coat must be applied within 24 hours. 3-5% by weight of quartz B0 or B1 (or hollow glass microspheres) can also be added to achieve a non-slip effect. In two coats, apply 0.25 to 0.40 kilograms of Syntech Pavicrom per square metre of surface to be covered. Can 5 kg [A] - Can 2.5 kg [A] - Can 5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B] - Kit: 1 Can 2.5 kg [A] + 1 Can 2.5 kg [B]

Syntech Pavistrong A two-component coating with a modified epoxy resin base, specific for protecting concrete surfaces destined to be in contact with aggressive agents or for containing food products and drinking water. Syntech Pavistrong is certified according to EN 1504-2, for the protection of structures in reinforced concrete as well as for food contact, in accordance with the requirements of Ministerial Decree 21/03/73 and subsequent amendments. Syntech Pavistrong is characterized by its excellent chemical resistance to aggressive exposure environments, to alkalis even at high concentration, to medium concentration acids and to the flow of liquids even containing solid suspensions. It is impermeable to water and chemically aggressive agents. It constitutes an effective barrier to the penetration of carbon dioxide and the carbonation of concrete. It is non-toxic, therefore suitable for contact with food and drinking water. It has excellent adhesion to concrete, steel, bricks, stone in general and various materials commonly used in construction. The fluid consistency makes Syntech Pavistrong fast and easy to apply both by brush and roller. Industrial concrete floors. Purification tanks for waste water and related technical rooms. Food tanks, pipes and containers. Digesters and plants for the production of biogas. Coating of canalizations and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containers for accidental spills of petroleum products, chemicals and food products. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to first apply the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Thoroughly mix the two components in their respective containers. Pour the can of component B into the can of component A, mix thoroughly for 2-3 minutes. To obtain a perfect mixing use a mechanical stirrer or a suitable tool. The mixture of the two components must be spread within 20-30 minutes, in order to avoid hardening in the can itself. Note that the reaction rate depends on the ambient temperature (at 30 ° C it hardens in 15 minutes). Apply on the surface to be treated, in two coats, within the indicated times, for an indicative consumption of 500-600 g / m². Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Do not dilute the components or the mixture of the two components. From 0.50 to 0.60 kg of SYNTYECH PAVISTRONG for each square metre of surface to be covered, for two coat applications (0.25-0.30 kg per single coat). Can 2 kg [A] - Can 6 kg [A] - Can 1 kg [B] - Can 3 kg [B] - Kit: 1 Can 2 kg [A] + 1 Can 1 kg [B] - Kit: 1 Can 6 kg [A] + 1 Can 3 kg [B]

Syntech Primer EP-W Syntech Primer EP-W is a solvent-free two-component epoxy resin to be used as a bonding primer for applying all epoxy cycles on concrete surfaces and concrete conglomerates in general. Syntech Primer EP-W is formulated to achieve an elevated impregnation, consolidation and adhesion effect of the substrate. It can also be used on wet surfaces. Syntech Primer EP-W even penetrates deep into compact surfaces, effectively consolidating the support. It also has a great resistance to water and aggressive solutions whilst allowing water vapour to pass through. Promotes adhesion for epoxy coatings as well as for porous and deteriorated substrates, along with acting as a cement and concrete consolidation agent. The support on which the epoxy, polyurethane or methacrylic system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric expansion, vibrations etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 4%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line or grouted with Syntech AS 21. In the event of the presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply the Syntech Pavidamp epoxy resin for "wet bottoms" beforehand. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Mix the two components, each in its own container, before combining. Pour component B into component A and mix for 3 to 5 minutes with a low-speed mixing drill to achieve the complete homogenisation of the mixture. The protective coating can be applied once the Syntech Primer EP-W is completely dry. Use 150 to 200 grams per square metre per coat, depending on the porosity and unevenness of the support. Can 10 kg [A] - Can 5 kg [A] - Can 5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Syntech Epox Timber Syntech Epox Timber is a liquid, transparent, two-component epoxy resin for incorporating thick objects, mass filled casting and the treatment of wood. Its self-levelling and non-yellowing nature, along with its scratch-resistance and fluid consistency, render it ideal for pouring and for filling any voids. The final effect of Syntech Epox Timber is a smooth and even surface with a transparency similar to glass. It is also possible to colour the product with specific pigments to achieve a coloured transparent effect. It is advisable to conduct preliminary tests to achieve the desired aesthetic effect. Syntech Epox Timber can be applied in thicknesses from 0.5 to 10 cm for the creation of tables and shelves in wood and resin, artistic creations and high thickness castings in which to incorporate small parts, stones, shells and objects in general, including metal . Higher thicknesses and castings without inserting embedded objects can cause overheating during the catalysis of the product. Syntech Epox Timber has excellent chemical resistance, abrasion, scratches and wear, has a high degree of transparency that lasts over time thanks to UV filters, the self-leveling consistency and low viscosity facilitate the elimination of bubbles air and allow to obtain planar surfaces, it does not contain solvents. Excellent resistance to water, basic solutions. Fair resistance to acids and solvents. Syntech Epox Timber is a transparent vitrifying resin to be applied by pouring for the construction of tables and wood-resin surfaces, by incorporating boards, fragments or sections of wood, even irregular, appropriately treated and thick coatings on even wood surfaces. If the support is absorbent, such as untreated wood or porous materials, it must be previously treated with the same Syntech Epox Timber applied by brush to avoid the formation of air bubbles. To make bulk filler castings, prepare suitable molds of the desired shape. Make sure you have 'leveled' the surface so that the resin can level itself correctly and thus a perfectly flat surface is obtained. Mix components A (basic formulation) and B (hardener) each in their own container before mixing; then pour component B into the container of component A. Mix everything for a few minutes using a mechanical stirrer at variable speed until a homogeneous mixture is obtained, with a uniform color and free of lumps. Do not take partial quantities from the packs to avoid any errors in the mixing ratio which would cause failure or incomplete hardening. After mixing, proceed by pouring the mixture into the previously prepared mold. High thickness castings require hardening times between 48-72 hours at a temperature of 25-30 ° C. To avoid surface defects or lengthening of the hardening time, it is advisable to work in an environment with a temperature of at least 25 ° C, a temperature to be maintained throughout the hardening period. The completely hardened product can be polished like normal lacquers paying attention to the residual elasticity, during the polishing process it is necessary to avoid overheating the surface to avoid temporary softening. Otherwise, you can proceed with the application of clear acrylics after having sanded the resin with 500/1000 paper. Approximately 11 kg / m² of Syntech Epox Timber for each centimeter of thickness to be created (approximately 1100 kg for each cubic meter). PACKAGING AND DIMENSIONS: Pail 0.7 kg [A] - Pail 3.5 kg [A] - Pail 0.3 kg [B] - Pail 1.5 kg [B] - Kit: 1 Pail 0.7 kg [A] + 1 Pail 0.3 kg [B] - Kit: 1 Pail 3.5 kg [A] + 1 Pail 1.5 kg [B]

ALWA HT RESIN is a resin-based on isocyanate and epoxy (EP), which reacts after adding a catalyst. ALWA HT RESIN offers a range of possibilities for producers of fibre-reinforced materials (e.g., glass fibre, kevlar and carbon), semi-finished and finished goods. The system is also suitable for prepreg and reaction compounds. ALWA HT RESIN is particularly interesting for the aerospace and aircraft industry as well for the rail transport, automotive and electronics industry. The application area of epic resins are electro casting resins, lamination and injection technology (RTM procedure), vacuum infusion, casting and ramming compounds, impregnation resin, casting and injection moulding process as well as prepreg technologies, among others. ALWA HT RESIN is offered in two versions. *ALWA HT RESIN M100 with approx. 50 mPa s *ALWA HT RESIN M2200 with approx. 2200 mPa s The resins can be mixed with one another which enables a flexible adjustment of the viscosity.

Wir bieten Ihnen die Möglichkeit, Formbewehrungen aller Art zu realisieren. Egal ob Fassadenplatten, Betonmöbel, L-Winkel oder runde Profile – basierend auf den bewährten solidian GRID- und solidian FLEX GRID-Bewehrungen erstellen wir eine Bewehrungsform gemäß Ihren Designspezifikationen.

Syntech IC 55 A two-component pure epoxy adhesive that is fluid with a low viscosity, free from fillers and solvents, being specific for high performance structural consolidation injections in crumbling masonry, degraded concrete, aging screeds and industrial flooring, cracked plasters and mortars and so on. It is ideal for securing bars, clamps and tie-rods. It is also perfect for the deep consolidation of wooden materials and other types of porous materials, with impregnation by brush or roller. Reinforcing and filling injections of cracks in concrete, stone, brick, mixed works etc. Anchor, bonding and attachment of connectors, plates etc. Structural reinforcement and small volume rebuilding (only horizontal) in general. Reinforcement of porous construction materials such as wood, natural stone, bricks etc. The surfaces of application will be seasoned and dry (residual humidity measured at a depth of 4 cm, should not be greater than 4 % ), free from dust, grease, soiling, crumbling and non-adhering parts. Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A taking care to remove all the material from the packaging, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mixture is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous lump-free mixture is obtained. Lay the material using the techniques specific to the type of intervention: injection, pouring, brushing, etc.. Do not apply on wet or pulverised media. Non-conformities of the support can have unpleasant drawbacks: detachments, large bubbles, etc. Apply only in the intended thermal intervention (+8/+35 °C). Use the product immediately after mixing and mix only the amount of product intended for immediate use. Syntech IC 55 is a product based on fluid epoxy resins. It may cause variations in the colour of the product on which it is applied, both wood and stone material. For this reason it is recommended to carry out preliminary tests. Approximately 1.1 kg of SYNTECH IC55 for each cubic decimetre of volume to be filled. Can 1 kg [A] - Can 5 kg [A] - Can 0.5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 1 kg [A] + 1 Can 0.5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Armaglass Grid 33 Armaglass Grid 33 is a square reinforcement gusset, with a side of 17 cm, made with glass yarn bars and pultruded epoxy resin. The monolithic, bidirectional mesh has a 33x33mm mesh, with a bar diameter of 3mm. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. Armaglass Grid 33 is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with Armaglass Structura meshes in pultruded glass for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Grid 33 is combined. Apply Armaglass Grid 33 together with the Armaglass Connectors provided in the reinforced plastering cycle, in order to guarantee greater structural collaboration between the mesh, connector and mortar of the RINFOR SYSTEM reinforcement system. Based on the connectors provided in the CRM system. Packaging: Bulk from 1 piece UM: €/piece

Syntech Acid Resistant Chemical-resistant coating based on modified epoxy phenolic resins, for the protection of walls, floors and concrete, steel and fiberglass structures. Two-component epoxy phenolic resin, applicable by spray, roller or spatula, for the coating and waterproof protection of structures subject to strong chemical aggression. Property: high mechanical and abrasion resistance, high adhesion to surfaces good elasticity high chemical resistance to acids, bases and solvents very high tenacity and ease of cleaning and maintenance high chemical resistance to petrol, fuels and hydraulic oil applicable in thick layers, even several times. Industrial floors in concrete. Waste water purification tanks and related technical rooms. Tanks, ducts and food containers. Digesters and plants for the production of biogas. Coating of pipes and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containment tanks for accidental spills of petroleum products, chemicals and food products. Protective coating of floors and walls of food, dairy, wine, breweries, distilleries, oil mills, oil mills. As a primer: 0.20 - 0.25 kg of Syntech Acid Resistant for each square meter of surface to be primed. As a coating: 0.40 kg of Syntech Acid Resistant for each square meter of surface to be coated. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Syntech Bioflex Anti-acid coating based on modified epoxy and polysulphide polymers, for the waterproof coating of concrete and steel tanks, tanks and containment tanks. High mechanical and abrasion resistance High adhesion to surfaces Good elasticity High chemical resistance to acids, bases and solvents Very high tenacity and ease of cleaning and maintenance Applicable to heavy thicknesses. Anti-acid waterproofing protective coating for the chemical industry Internal and external lining of tanks, tanks, cisterns, towers, pylons, etc. Waterproof protective coating of digesters of biogas and purification plants Anti-acid protective coating for sewers, secondary tanks, sewer collectors, channels and ducts intended for the containment of waste water and drainage Anti-acid coating of fiberglass tanks for the chemical industry. From 0.40 to 0.50 kg of Syntech Bioflex for each square meter of surface to be covered, applied in two coats. Can 6.1 kg [A] - Can 3.9 kg [B] - Kit: 1 Can 6.1 kg [A] + 1 Can 3.9 kg [B]

Syntech AS 31 The two-component structural epoxy adhesive putty is soft, thixotropic and spatulable (malleable paste), ideal for anchoring steel connectors, hermetically sealing through-holes in concrete, bonding steel plates on concrete surfaces, as an accessory product for laying road joints, for the reconstruction of wooden beam heads, repairing cracks and reconstructing missing geometries, fixing injectors, reconstructing joints in concrete flooring and fixing Elastotex 250 Combi elastic strips, including when in contact with water destined for human consumption. Structural reinforcements of structural elements (beams, pillars, etc.) by bonding steel sheets to the concrete. Reconstruction of joints in concrete floorings. Rigid structural bonding (beton plaque) of prefabricated elements and of articles in different building materials: concrete, steel, glass, wood, marble, tiles, stones etc. Anchoring, bonding and attachment of connectors, ties etc. Attachment of elastic straps for waterproofing joints, Elastotex. Reconstruction of wooden heads, crack repair, reconstruction of missing geometries on various supports. The application surfaces must be suitably prepared and adequately resistant: free from dust, grease, soiling, crumbling and non-adhering parts, devoid of wet surface areas. For floorings, moreover, a shot peening or preliminary milling of the surfaces of adhesion is recommended. The metal elements are to be blasted to "almost white metal". Make sure that the environment is well ventilated and wear the personal protective equipment mentioned in the safety data sheet. Add component B to component A, taking care to remove all the material from the packaging and mixing thoroughly with a mixer at a low number of revolutions (or a suitable manual tool), until a homogeneous mixture is obtained, indicated by the uniform colour and the absence of lumps. Apply to the surfaces with the help of spatulas, trowels, etc. Complete the tasks during the useful life of the product. Do not apply in rainy days; do not apply on moist or wet supports; do not apply on pulverised supports; use the product immediately after mixing. Approximately 1.6 kg of Syntech AS 31 for each cubic decimetre of volume to be grouted. Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 0.5 kg [B]

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Une fois la préparation de votre sol terminée, nous passons au rebouchage de fissures et de l’application d’une primaire Epoxy.

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Syntech Pavicar Two-component coating based on epoxy and polyurethane resins; for the coating, waterproofing and elastic protection of roofs, terraces, pavements, stairs, car parks and surfaces that are cracked or subject to micro-cracks and crazing. High wear resistance Applicable on tarred surfaces and bituminous sheaths Walkable product suitable for covering and waterproofing flat roofs Ease and speed of application with quick intervention times Soft and velvety to the touch Elastic product resistant to dynamic stress Available in two colors. Waterproof coating of concrete, ceramic, porcelain stoneware, wood, sheet metal supports, tarred supports and bituminous sheaths, suitably primed. Creation of elastic and waterproof protections for multi-level parking areas, both internal and external. Ideal for waterproofing cycles of balconies, roofs and terraces as it does not require preliminary demolition work or replacement of coverings. Its application allows the creation of a continuous, elastic and waterproof layer resistant to wear and trampling. Approximately 2.0 kg of Syntech Pavicar for each square meter of surface to be covered, in two coats. Can 8.3 kg [A] - Can 16.7 kg [A] - Can 4.17 kg [A] - Can 1.7 kg [B] - Can 3.3 kg [B] - Can 0.83 kg [B] - Kit: 1 Can 4.17 kg [A] + 1 Can 0.83 kg [B] - Kit: 1 Can 8.3 kg [A] + 1 Can 1.7 kg [B] - Kit: 1 Can 16.7 kg [A] + 1 Can 3.3 kg [B]

olidian REBARs kombinieren hochfeste Fasern mit extrem widerstandsfähigen Harzen im Produktionsprozess Pultrusion. Hier sind Kohlenstoff- oder Glasfasern extrem gerade ausgerichtet, mit Harz imprägniert und gehärtet. solidian REBARs realisieren unglaublich hohe und langlebige Tragfähigkeiten für extremste Anforderungen. Dies ist das Ergebnis der Kombination der Geradheit der Fasern und der wählbaren großen Durchmesser des Querschnitts. Als solche sind solidian REBARs vor Ort zugänglich. Sie sind daher der ideale nicht korrosive Ersatz für metallische Verstärkungen für alle, die an wirtschaftlicher und ökologischer Nachhaltigkeit interessiert sind.

Armaglass Corner 33 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh with a side of 33 mm, an ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 33 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 33 is combined. Apply Armaglass Corner 33 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Packaging: Loose from 1.05 meters UM: €/piece

Armaglass Corner 99 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh with a side of 99 mm, an ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 99 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 99 is combined. Apply Armaglass Corner 99 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Based on the total length of the corner areas. Packaging: Loose from 1.05 meters UM: €/piece

Armaglass Corner 66 Angular element of monolithic GFRP mesh made with continuous filament glass fiber yarn bars and pultruded epoxy resin primer. The bars are intertwined with each other through a stitching thread, using a unique technology that allows the formation of joints between the longitudinal and transverse bars with high mechanical resistance. The epoxy resin guarantees the mesh high dimensional stability, alkali resistance and improves the mechanical characteristics. The composite has a square mesh of 66 mm side, ideal size for use with mortars for CRM reinforcement systems. The corner piece is a component of our RINFOR SYSTEM systems, which also include GFRP networks, gussets and connectors combined with our lime-based or cement-based mortars. To be used in combination with the Armaglass Structura 66 mesh for the reinforcement of masonry and concrete structures through the reinforced plaster technique (CRM system: Composite Reinforced Mortar). To prepare the support, carefully follow what is indicated in the technical data sheets of the mortar with which Armaglass Corner 66 is combined. Apply Armaglass Corner 66 in correspondence with all the corner areas of the reinforced plastering, in order to guarantee the structural continuity of the RINFOR SYSTEM reinforcement system. Based on the total length of the corner areas. Packaging: Loose from 1.05 meters UM: €/piece

NTC temperature sensors coated with epoxy resin have a very low temperature tolerance classification and a wide measuring range of -40…+150 °C. Name:NTC temperature sensor Sensor:NTC Temperature measuring range:-40...+150 °C Nominal resistance:1 kΩ Resistance tolerance:±1% Response time temperature:1 s in liquids Housing:Epoxy resin coated Beta constant:3348 K ±1.0% Self heating:0.85 mW/K Connection wires:Ø 0.5 x 65 mm, 10 mm uninsulated, silver-plated copper with white Teflon® insulated Dimensions:Ø2.5 x 69 mm Producer:Measurement Specialties, Inc. Producer article number:1K2A1B Weight:0.0014 kg

Il est indispensable de préparer votre sol pour qu’un revêtement de sol en résine Epoxy puisse être posé. Notre entreprise vous propose des techniques à la pointe : Le Grenaillage : Méthode de projection de micro-billes d’acier sur le sol. Il permet de préparer votre sol à un décrassage et décapage de peinture pour obtenir une rugosité et améliorer la qualité de votre surface. Ponçage : Méthode qui permet de lisser et de remettre votre sol à niveau pour une meilleure adhérence à la résine. Rabotage au sol : Méthode pour décaper en profondeur votre sol voir retirer une surépaisseur de béton. Pour une réalisation optimale, nous disposons de machines hautement performantes pour travailler sur des supports sans poussières car équipées d’un système d’aspiration, sans vibrations et limitent les nuisances sonores.

RJS Industrie Résine France intervient dans le marquage urbain (parking, délimitation de voiries, gestion des voies de circulation interne, de pistes cyclables…), le marquage de centre logistique tels que les quais de charge ou encore le marquage privatif. Nous utilisons des codes couleurs pour délimiter les différentes zones de travail : engins et/ou piétons. Pour cela, nous réalisons différents types de marquage : piéton, zébra, bande de délimitation… N’hésitez pas à nous formuler vos demandes afin que nous vous apportions une réelle analyse et expertise sur vos besoins. Marquage au sol intérieur Nos équipes vous apporteront leur expertise et leur l’accompagnement pour la création de vos espaces (sécurisation des zones à risques, la délimitation des espaces de stockage, la matérialisation des sens de circulation…)

NTC temperature sensors coated with epoxy resin have a very low temperature tolerance classification and a wide measuring range of -40…+150 °C. Name:NTC temperature sensor Sensor:NTC Temperature measuring range:-40...+150 °C Nominal resistance:1 kΩ Resistance tolerance:±1% Response time temperature:1 s in liquids Housing:Epoxy resin coated Beta constant:3348 K ±1.0% Self heating:0.85 mW/K Connection wires:Ø 0.5 x 65 mm, 10 mm uninsulated, silver-plated copper with white Teflon® insulated Dimensions:Ø2.5 x 69 mm Producer:Measurement Specialties, Inc. Producer article number:1K2A1B Weight:0.0014 kg

Die perfekte Industriebodenbeschichtung mit Epoxidharz für stark frequentierte Bereiche in nur einem Anstrich: Robust, langlebig und chemikalienbeständig! Verfügbar in vielen Farben und Variationen!

Die perfekte Industriebodenbeschichtung mit Epoxidharz für stark frequentierte Bereiche in nur einem Anstrich: Robust, langlebig und chemikalienbeständig! Verfügbar in vielen Farben und Variationen!

Die perfekte Industriebodenbeschichtung mit Epoxidharz für stark frequentierte Bereiche in nur einem Anstrich: Robust, langlebig und chemikalienbeständig! Verfügbar in vielen Farben und Variationen!

Die perfekte Industriebodenbeschichtung mit Epoxidharz für stark frequentierte Bereiche in nur einem Anstrich: Robust, langlebig und chemikalienbeständig! Verfügbar in vielen Farben und Variationen!

Die perfekte Industriebodenbeschichtung mit Epoxidharz für stark frequentierte Bereiche in nur einem Anstrich: Robust, langlebig und chemikalienbeständig! Verfügbar in vielen Farben und Variationen!

Die perfekte Industriebodenbeschichtung mit Epoxidharz für stark frequentierte Bereiche in nur einem Anstrich: Robust, langlebig und chemikalienbeständig! Verfügbar in vielen Farben und Variationen!

Araldite® AW 136H Harz Hinweis: Es handelt sich bei diesem Produkt um das Stammmaterial eines Zweikomponentensystems. Alle angegeben technischen Daten beziehen sich auf die Verwendung mit dem Standardhärter Die u. a. Eigenschaften beziehen sich auf den empfohlenen Härter HY991 (Siehe unter „Zubehör“ unten auf dieser Seite.) Pastöser Zweikomponentenklebstoff auf Epoxidharzbasis • Gute Beständigkeit bis 90°C • Besonders zur Verklebung von Metallen und einiger Kunststoffe geeignet • Leicht zähflüssig Araldite® AW 136 H / Hardener HY 991 ist ein bei Raumtemperatur aushärtender, leicht zähflüssiger Allzweck-Zweikomponentenklebstoff. Der Klebstoff zeichnet sich durch gute Kontakthaftung und Zähigkeit aus und eignet sich zum Verbinden einer Vielzahl von Metallen, Keramik und der meisten gebräuchlichen Werkstoffe. Nettogewicht: 1 EAN:4260534180432 kg:1