Produse pentru testează (2738)

Heizen und Kühlen kostet auf dem Weg zur Elektromobilität noch viel Reichweite, denn der benötigte Strom muss von der Batterieleistung abgezweigt werden. Um die Energieeffizienz zu steigern, gilt es, Klimaaggregate unter realistischen Bedingungen zu testen. Der Funktionsprüfstand von Poppe + Potthoff Maschinenbau (PPM) ermöglicht es, aufwändige Langzeittests bei wechselnden Temperaturen schnell und vor Ort durchzuführen. Wahlweise wird dabei eine Stromversorgung über die Bord- oder Traktionsbatterie mit Nieder- bzw. Hochspannung simuliert. Die Entwicklungszyklen werden immer kürzer – besonders in der Automobilindustrie, die sich zunehmend auf die Fertigung von Elektrofahrzeugen ausrichtet. Um sich auf neue Anforderungen rasch einzustellen, benötigen Zulieferer nicht nur gute Ideen für Produkte, sondern auch Anlagen, die eine schnelle Validierung ermöglichen. Prüfstände von Poppe + Potthoff Maschinenbau sind darauf ausgelegt, Prototypen oder Serienteile realitätsnah, schnell und... Batteriesimulation High Voltage:0 bis 600 VDC / 150A Batteriesimulation Low Voltage:0 bis 20 VDC / 5A Heizleistung elektrisch:25 kW Kälteleistung:15 kW bei -35° C Medientemperatur:-35° C bis +100° C Püfmedium:Wasser - Glykolgemisch / reines Glykol Umgebungstemperierung:-40° C bis +140° C Volumenstromregelung:3 bis 30 l/min

The rapid Screen Test Igg Sars-Cov-2 S-RBD test from whole prick blood is a rapid immunochromatographic test for the qualitative detection of IgG antibodies to the receptor binding domain (RBD) spike (S) protein of SARS-CoV-2 in human whole prick blood at approximately 10 days after vaccination. Screen Test Covid-19 Igg Sars-Cov-2 S-RBD is an in vitro diagnostic medical device CE 1434. Read the warnings and operating instructions carefully. PHARMACIST CODE:983834096

After 46 years, and 275,000 testers installed in more than 5,000 customers worldwide, ATEQ presents its revolutionnary flow tester: D670. New electronic module, new measurement module, new interface, new accessories… All has been made to improve your quality control. And yet, inside can be found the latest leak testing technics and technology that will garantee you the fastest and most accurate leak testing cycle on the market. Automotive, domestic appliances, medical, aeronautic, defense, fluid and electrical components, food and cosmetic packaging Flow measurement in direct or indirect testing Continuous measuring mode Wide flow measurement range USA, S.I. and customer units Measurement in standard or customised conditions Recalculated flow at the nominal pressure Measurement element fully integrated into one module 128 programs Mechanical or electronic regulator from vacuum to 10 bar Weight:7 Kg Dimensions:(WxHxD) 540x160x380 mm Operating:+ 5°C at + 45°C Storage:0°C at + 60°C

Crema Anti-Age Scopri il Prodotto L'azione anti-age della crema viso e contorno occhi Staminax è determinata dalla sapiente miscelazione di ingredienti della tradizione cosmetica con attivi innovativi. Contiene un preparato brevettato di due principi attivi estratti da cellule staminali vegetali, per una tripla azione, dalla rivoluzionaria performance anti-age. La crema viso e contorno occhi anti-Age Staminax è sviluppata, prodotta e confezionata in Italia da professionisti farmaceutici e cosmetici con esperienza decennale. La Formula I due attivi, sono inclusi in una formula preziosa, con Olio d'Argan, Olio di Jojoba, Olio di Vinaccioli e Burro di Karatè. Per un prodotto sublime 99,8% di ingredienti Naturali 50,2% di ingredienti Biologici Senza Profumo Senza Parabeni Senza OGM Senza derivati animali Vegano Non testato su animali L'Efficacia Il potere Anti-Age della crema viso e contorno occhi Staminax è garantito dall'alto contenuto di estratti da cellule staminali vegetali. Il primo stimola le nostre cellule a produrre collagene normalmente presente nella pelle umana, donando elasticità alla pelle, prevenendo e riducendo le rughe. Il secondo stimola la degradazione della bilirubina riducendo le occhiaie e migliora la microcircolazione riducendo le occhiaie. Gli Studi Sicurezza e Efficacia: Dermatologicamente testato su pelli sensibili, studio condotto su 25 volontari e sotto supervisione di un medico dermatologo. Nichel Tested Testato per altri 8 metalli pesanti Efficacia testa in Vivo, studio condotto su 30 volontari e sotto supervisione di un medico dermatologo. Per aproffondimenti visita il sito :https://www.staminax.it/staminax-antiage.

SARS-CoV-2 RT-LAMP Test de diagnostic rapide in vitro pour la détection du coronavirus SARS-CoV-2. GRIPPE A & GRIPPE B RT-LAMP Test de diagnostic rapide in vitro pour la détection des virus de la grippe A et de la grippe B.

Anwendung bei Lenkdynamik- und Fahrdynamikuntersuchungen sowie gesetzlichen Handlingtests. Das System zeichnet sich besonders durch extrem hohe Positioniergenauigkeit und Stellwinkelgeschwindigkeit auch bei höheren Stellmomenten aus - z.B. bei Ausfall der Lenkhilfe. Dieser Lenkroboter wurde speziell so konstruiert, daß die Funktion des Airbags des fahrzeugeigenen Lenkrads bei montierter Aktuatorik nicht beeinschränkt oder beeinflusst wird. Bei abgeschaltetem Antrieb kann das Fahrzeug vom Fahrer gelenkt werden. Testabläufe können im Stand-Alone Betrieb erstellt und ausgeführt werden. Ebenso kann das System an eine übergeordnete Automatisierung integriert werden. Verschiedene Konfigurationen und Erweiterungen wie weitere Aktuatoren (Gas, Brems, Kupplung, Schalten etc.), zusätzliche Regelungsarten sowie verschiedene Integrationsschnittstellen sind verfügbar.

FE-S1 Compression seal - silicone seal - suitable for blunt connections - for sealing joints up to 10mm distance silicone seals - silicone sealing profiles, suitable for indoor and outdoor installations - made of permanently elastic silicone, age-resistant, permanent sealing property - emission-free and conservation tested - certified to British Museum Standards, Oddy tested - 60 Shore A

Le CP300DS est l'outil parfait pour la radiographie numérique. Son petit point focal génère des images plus nettes et plus claires, ce qui vous permettra de détecter avec précision le moindre défaut lors de vos inspections NDT. Avec son tube métal-céramique et sa large plage de tension de sortie (jusqu'à 300 kV), ce générateur portable à potentiel constant est également un partenaire robuste pour une large gamme d'applications NDT. Le CP300DS est équipé de notre célèbre carrousel intégré avec 5 positions de sortie et a un cycle de service de 100 % à 30°. Il fonctionne avec l'unité de contrôle POWERBOX plug-and-play, comme le reste de la gamme de produits CPSERIES. Géométrie de radiation : Directionnelle Plage de tension de sortie kV : 30 à 300 Plage de courant du tube mA : 0,5 à 6 Courant du tube à pleine sortie mA : 3 Puissance max. à l'anode W : 900 Mode de puissance constante : Oui Cycle de travail à 30°C % : 100 Pénétration dans l'acier mm : 66 Poids Kg : 29 Dimensions globales mm : Ø 180 x 837 Dose de fuite à 1 m à pleine sortie mSv/h : < 5.0 Point focal optique (EN12543) mm : 1 Angle utile max. ° : 60 x 30 elliptique Filtration inhérente mm Be : 0.8 Niveau d'étanchéité : IP65 Température de fonctionnement °C : -30 à +60 Température de stockage °C : -40 à +70 Carrousel intégré avec 5 sorties : Oui Anneaux de protection : 2

A special probe design allows contacting with very high currents and very low contact resistances. Additional functions like temperature sensors or sense pins can be integrated, even at limited space.

Our experts manufacture various wood specimens from common wood grades. During production, we attach great importance to using wood that is free of cracks and knots. We also pay attention to the annual ring position of the wood when selecting the material. Do you wish to order further processing by grinding or drilling? Then this is the right place. Further types of wood:available upon request Wooden boards:According to EN 205, EN 304 (beech) According to EN 927 (pine and spruce) Consumables:such as stirring rods

Höhendetektor

Calibrate and adjust mechanical yarn brakes for the textile industry The test specimen is inserted in the UUT, which is mounted on a pneumatic slide. By pressing a button, the candidate moves to the running belt drive. The sample is then tested in different locking positions, the switching of the individual Paramtersätze is realized via a rotary switch. In each latching position, IO / NIO statement about the GMV2 light mounted on the column is displayed visually. After passing the examination, the tray will open again and the next candidate can be inserted. A speed controller as well as an ON / OFF switch for the drive are also integrated in the switch box under the GMV2. The entire inspection unit is mobile and complained to a height-adjustable lifting unit. The GMV2 and connect the switch are also mounted height adjustable in the profiles.

DESCRIPTION The Torque Powder Brakes (TPBSeries) are ideal for applications operating in the low speed range or middle to-high torque range. These magnetic powder brakes provide full torque at zero speed and are convection or air cooled, allowing power ratings up to 900W (2100W with air cooling). APPLICATIONS These units are suited for tension control applications, such as wire winding, foil, film, and tape tension control. Mounted on test benches, TPB Series - Torque Powder Brakes allow performance and reliability testing on driving elements such as electric motors, hand-held power tools, geared motors, reduction gears, and hydraulic transmission systems. Other applications include load simulation for life testing on electric motors, actuators, gearboxes, power steering, and many other rotating devices and assemblies. Available torque ratings:12, 25, 50, 100, 200, 400, 600N·m Braking power:up to 900W (2100W with air cooling) Rated torque available from:0rpm

End-of-Line (EoL) testing devices are used to test the quality of the product after the production process. The purpose of the testing system is to check any visual, audio or other problems that may arise during the installation and assembly of components before they are delivered to customers. Application examples of end-of-line testing systems developed by Novosim include: ​ Rotary systems (transmissions, axles, etc.) Automotive Component Testing Noise and vibration level measurements special systems ​ EoL testing systems are complex systems that generally operate automatically and include a range of sensors, data acquisition devices and testing equipment. Test procedures can be prepared in the form of predefined scenarios by the development team and stored in a database. Different scenarios can be prepared for different test conditions (high speed, low speed, long term, short term, etc.) and then called from the database.

PP (Polipropilen) 12x75 Steril Olmayan 12x75 Kan (Test) Tüpü, PP (Polipropilen) malzemeden üretilmiş, non-steril özelliklere sahip bir tüptür. Ürün Kodu:AKL-849

This unit was designed and built for protection of workstations mobile or permanent on the battlefield or in defense of sen- sitive targets, air-transportable as it is of limited weight and size. Aimed at the protection of operators armed. Front tilted 30 degrees with 8 mm x 70 mm slots suitable for hooking the side panels. Side panels dimensions 1000 x 1000 mm base 900 mm hypotenuse 970mm. Certification: Banco Nazionale di Prova per le Armi da Fuoco Portatili e per le Missioni Commerciali: - Prot. N°22/BAL-AG/vp February 23, 2010. Bullet ballistic resistors 5.56 x 45 SS109 + 7.62x51 Nato. Weight:27,00 kg Hooks:SNAP A BAYONET Material :POLYETHYLENE HD

We cooperate with manufacturers of individual testing solutions for electronic boards. We guarantee their excellent quality and effective and cost-optimal solutions.

Servizio di sviluppo di una micro campionatura per testare il mercato. Questo tipo di servizio permette di replicare in modo fedele il prodotto in scala industriale, ma con minimi contenuti.

Teststifte: - sind von 28 bis 60mN/m in 1er Schritten und von 62 bis 70mN/m in 2er Schritten verfügbar - Genauigkeit +/-1,0mN/m Stifte BLAU sind von 28 bis 60 mN/m in 1er Schritten und von 62 bis 70 mN/m in 2er Schritten verfügbar • Genauigkeit +/- 1,0 mN/m • Ablesezeit 2 sec. • Einfache Handhabung • Kein Verschütten möglich

RPWORLD Injection Molding service provides high accuracy and consistency for your custom parts. How to achieve that? The combination of our stringent quality control and stage-of-the-art quality inspection equipment ensures the consistency and high quality for your different batch of parts. - Consistent high quality RPWORLD stringent quality control combining with stage-of-the-art inspection equipment ensures the highest quality for your different batch of parts. - 30+ engineering-grade materials 30+ plastic materials in stock, including glass fiber, nylon with carbon fiber, talcum powder, glass bead, and materials of anti-high temperature, flame-resistance, anti-impact, food-grade and medical-class. - Short lead times With automatic equipment working 24/7, our injection molding service help you get custom parts in as fast as 7 days. Industries Applied: - Medical Device Manufacturing - Automotive - Scientific Instrument - Mechanical Engineering - Robotic - Design Industries Applied:Medical Device Industries Applied:Scientific Instrument

Rollos de papel kraft gigantes Referencia:702

The SEC 6100 is part of the Solar Technology by Atlas market approach offering integrated, ready-to-use test chambers for various solar and environmental applications. The SEC 6100 combines environmental simulation with metal halide lighting technology. It's a full function climatic chamber with additional simulation of the global sunlight spectra. Exposure volumes of 14m 3 are offered within the largest standard double door walk-in solar environmental chambers for e.g. multiple full PV modules testing. Test chamber capacity approx. 14,200L Radiation area approx. 48,000cm 2 Lamp: 6x MHG 4,000W Luminary Intensity: 800W ~ 1200W /m 2 (Adjustable) Wavelength: 280 ~ 3,000nm (Full Spectrum) -30℃ ~ +100 °C (W/O Radiation) -20℃ ~ +100 °C(W/ Radiation) 30% ~ 95%RH (W/O Radiation) 20% ~ 80%RH (W/ Radiation) 12.1" color touch screen Graphic User interface Intuitive control features and easy-to-use programming logic 6 Channel DAQ integrated for temperature sensors Multi-source temperature control pre-implemented and selectable in user interface Pre-wired for BST (Black Standard Temperature) sensor and control Pre-wired for plug-and-play radiometer for irradiance measurement Galvanized steel with powder coated exterior Engineered diffusive reflective stainless steel inner testing chamber for optimum spatial uniformity Easy access swing doors to luminary systems Robust refrigeration system for precision control of environmental parameters Multi-stage safety features Option Atlas25+ Core Cycles Indoor Filter Pyranometer CMP6 Class 1 - General Purpose Black Standard Temperature (BST) Controlling the Black Standard Temperature (BST)

Tub de policarbonat de 16x110 / Tub de testare cu capac file - Tub de policarbonat CODUL PRODUSULUI:019 Sterilizat:Autoclave 121 ° Resistant Materii prime:Policarbonat Numărul codului de bare:8682009086432 Număr de catalog:MK.09.432

• Con utensili di alta qualità, isolati e testati a norma DIN EN/IEC 60900 • Sortimo I-BOXX, cassetta in plastica ABS resistente agli urti e ai colpi con coperchio trasparente chiudibile • Cassette Insetbox per sistemi di classificazione e suddivisioni Lunghezza in millimetri:367 Peso in grammi:1575

Tutti i nostri prodotti sono realizzati presso la nostra sede. Durante il ciclo produttivo dei nostri prodotti sono eseguiti collaudi intermedi. Alla fine del ciclo produttivo sono, invece, eseguiti collaudi a tappeto: il 100% dei nostri prodotti viene sottoposto a collaudo prima della consegna al cliente finale. Su ciascun prodotto sono eseguiti i test che possano verificarne la conformità rispetto alle specifiche del cliente, ai parametri progettuali ed alle norme CEI di riferimento. Tutti gli strumenti utilizzati per il collaudo sono soggetti a taratura presso laboratori certificati Accredia.A titolo puramente esemplificativo ed a seconda della tipologia di prodotto possono essere eseguiti i seguenti test (ed altri non elencati): Test di rigidità dielettrica;

Das Digitalmanometer DM 01 ist ein Präzisionsmessgerät, welches höchsten Ansprüchen gerecht wird. Es wurde speziell für die Prozessüberwachung und Kalibrierung konzipiert. Der Vorteil: Das DM 01 besteht aus zwei Geräten – der Digitalanzeige und einem Druckmessumformer. Herausragende Messeigenschaften, intuitive Bedienung, sowie sein innovatives, modulares Sensorkonzept zeichnen das DM 01 aus. Das batteriebetriebene Digitalmanometer kann z. Bsp. zur Überwachung von Druckverläufen und zur Kalibrierung von Druckmessumformern verwendet werden. Merkmale: — Nenndrücke: 0 ... 100 mbar bis 0 ... 400 bar — Genauigkeit: 0,05 % FSO BFSL (Klasse 0,05) — modulares Sensorkonzept — grafikfähiges Display — Hintergrundbeleuchtung — USB 2.0 Schnittstelle — Edelstahlgehäuse d = 100 mm — Nullpunkt-Justage — Datenlogger Optionale Merkmale: — Kalibrierzertifikat nach DKD / DAkkS — Ex-Ausführung Zone 0/1 — Kalibrier- und Prüfkoffer mit umfangreichem Zubehör

The UV test chamber BS-04 is large, robust equipment for the time- or dose-controlled irradiation of samples with UV light. The chamber can be fully equipped for one of the spectral regions UV-C, UV-B, or UV-A to achieve the highest irradiance. Alternately, the use of two separately controlled lamp groups for different spectral regions allows for especially flexible operation of the chamber. The interior irradiation chamber has a base area of 86 x 65 cm² and a height of 32 cm. The sliding sample carrier facilitates loading and unloading. With a load of up to 20 kg, this can withstand all demands. The sample chamber operating temperature is about 25°C so that thermal damage to the specimen is avoided. Due to the high uniformity of the irradiation, the samples may be positioned in any order. The BS-04 can be equipped with two irradiation controls: the UV-MAT and the UV-MAT Touch. Interior chamber:86 x 65 x 32 cm Dimensions:95 x 73 x 70 cm Power consumption:400 W Lamp lifetime UVA:up to 4.000 h Lamp lifetime UVB:up to 4.000 h Lamp lifetime UVC:up to 9.000 h Irradiance UVA:8 mW/cm² Irradiance UVB:5 mW/cm² Irradiance UVC:12 mW/cm²

Der Prüfstand P 250 mit Control C.2P ist ein neuer modularer Prüfstand, der an Ihre Bedürfnisse angepasst werden kann. Er bietet die Möglichkeit, Steck-0-, Hand- oder Hydraulik-Schnellspannsysteme zu verwenden. Im Inneren des Prüfstandes findet eine ganze Europalette Platz. Die Kammer arbeitet auch mit einer Endlos-Verlängerung, wenn Sie einen Schlauch auf seiner ganzen Länge auf seine Dichte prüfen möchten. Über die Steuerung Control C.2P können sie alle Parameter für einen vollautomatischen Test mit Visualisierung des Drucks und weiterer Funktionen kontrollieren, aber auch Verbindungen zu Ihrem Server oder anderen vernetzten Geräten erstellen. Qualität und Innovantion als Garant •Vollständig geschlossener Prüfraum •Schnellfüllung und automatische Entlüftung der Prüfstücke •Einfachste und problemlose Handhabung •Wechsel zwischen automatischem und manuellem Einrichtbetrieb •Bis zu 120 Prüfungen pro Stunde bis zu einer Länge von 2500 mm (DN 12-800 mm) möglich Testart:hydrostatischer Druck Getestetes Produkt:Schlauch,Flaschen,für Ventil Technologie:hydraulische,digitale

Mejora la sostenibilidad de tus eventos y competiciones deportivas con la cinta de señalizar compostable. Alternativa sostenible al plástico fósil. Fabricada con biopolimeros orgánicos que en su degradación no contaminan ni genera microplásticos. Diseñada con poco grosor para facilitar su colocación en diferentes localizaciones en el monte. Personalizable y disponible en stock. Fabricada según estándar Europeo EU 13432 y con certificado TUV Austria. Fabricada 100% en Europa. Estandar amarilla en stock:8 cm de ancho X 500 metros de largo

Werkstoff: Spannbuchse 1.0711. Zylinderschraube Stahl. Ausführung: Spannbuchse brüniert. Zylinderschraube verzinkt. Hinweis: Zylinderschraube DIN 912 wird mitgeliefert. Bei B0004-081X12 Spannbuchse blank.