Produse pentru săgeți cu oțel inoxidabil (1039)

The installation system consists of high-quality NiroSan® Gas press fittings with yellow moulded sealing rings made of HNBR (hydrogenated nitrile butadiene rubber) and NiroSan® stainless steel system pipes according to EN 10312, DVGW-Arbeitsblatt GW 541 and EN 10312. All NiroSan® Gas press fittings are made of the material 1.4404 / AISI 316L (for moulded fittings) and 1.4408 (for threaded fittings and stainless steel precision castings). The material contains at a minimum of 2.3 % molybdenum and a lower carbon content than the conventional steel quality 316. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® Gas press system is certified in accordance with and all important European certification bodies.

The installation system consists of high-quality NiroSan® Gas press fittings with yellow moulded sealing rings made of HNBR (hydrogenated nitrile butadiene rubber) and NiroSan® stainless steel system pipes according to EN 10312, DVGW-Arbeitsblatt GW 541 and EN 10312. All NiroSan® Gas press fittings are made of the material 1.4404 / AISI 316L (for moulded fittings) and 1.4408 (for threaded fittings and stainless steel precision castings). The material contains at a minimum of 2.3 % molybdenum and a lower carbon content than the conventional steel quality 316. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® Gas press system is certified in accordance with and all important European certification bodies.

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® pipe Bend 90° female/male

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Elbow 90° F/F-thread

SANHA stainless steel heating circuit distributors are suitable for all hot water heating systems in accordance with EN 12828, and for panel heating / cooling systems in accordance with EN 1264, and can therefore be used not only in residential buildings, but also in industrial, commercial and public buildings. Material:Stainless steel 304 Operating pressure:Max. op./test pressure: 4,0 / 6,0 bar Operating temperature:-10 °C - 80 °C

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Bend 90° female/male - long

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Bend 45° female/female

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Male adaptor

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Tee

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Bend 75° with plain ends

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. The heating power is steplessly adjustable and the thermostat keeps your chosen temperature constant. Choose either frost protection or your temperature between + 5°C and + 30°C. The red signalling light shows when power is on. Power:500W - 3000W Voltage:230 V lenght:440mm - 1440mm Protection mode:IP66 / IP67

Rohrleitungssystem aus hochwertigen NiroSan®-Pressfittings (Edelstahlfittings) mit einer Formteildichtung aus EPDM (Ethylen-Propylen-Dien-Kautschuk) und NiroSan®-Edelstahl-Rohren nach DVGW-Arbeitsblatt GW 541 bzw. DIN EN 10312. Alle NiroSan®-Edelstahlfittings werden aus den Werkstoffen 1.4404 / AISI 316L (Formteile aus Edelstahl) und 1.4408 (Gewindeteile, Edelstahl-Feinguss) gefertigt. Der Werkstoff enthält mindestens 2,3 % Molybdän und weist einen geringeren Kohlenstoffanteil als der konventionelle Werkstoff 1.4401 auf. Damit ist er nicht nur gleichwertig zu diesem Edelstahl, sondern überzeugt durch seine deutlich höhere Korrosionsresistenz. Das NiroSan®-Presssystem ist geprüft nach den DVGW-Arbeitsblättern GW 541 und W 534 und zugelassen von DVGW, ÖVGW, SVGW sowie allen namhaften europäischen Zertifizierungsstellen. Die NiroSan®-Serie 9000 ist auch in einer speziellen LABS*- und silikonfreien Ausführung mit EPDM-Dichtring und in einer separaten Verpackung erhältlich. O ring:EPDM Operating pressure:16 bar Operating temperature:-30 - 120 °C Dimension:15 - 108 mm

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Elbow 90° female/male-thread

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The installation system consists of high-quality NiroSan® Gas press fittings with yellow moulded sealing rings made of HNBR (hydrogenated nitrile butadiene rubber) and NiroSan® stainless steel system pipes according to EN 10312, DVGW-Arbeitsblatt GW 541 and EN 10312. All NiroSan® Gas press fittings are made of the material 1.4404 / AISI 316L (for moulded fittings) and 1.4408 (for threaded fittings and stainless steel precision castings). The material contains at a minimum of 2.3 % molybdenum and a lower carbon content than the conventional steel quality 316. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® Gas press system is certified in accordance with and all important European certification bodies.

Rohrleitungssystem aus hochwertigen NiroSan®-Pressfittings (Edelstahlfittings) mit einer Formteildichtung aus EPDM (Ethylen-Propylen-Dien-Kautschuk) und NiroSan®-Edelstahl-Rohren nach DVGW-Arbeitsblatt GW 541 bzw. DIN EN 10312. Alle NiroSan®-Edelstahlfittings werden aus den Werkstoffen 1.4404 / AISI 316L (Formteile aus Edelstahl) und 1.4408 (Gewindeteile, Edelstahl-Feinguss) gefertigt. Der Werkstoff enthält mindestens 2,3 % Molybdän und weist einen geringeren Kohlenstoffanteil als der konventionelle Werkstoff 1.4401 auf. Damit ist er nicht nur gleichwertig zu diesem Edelstahl, sondern überzeugt durch seine deutlich höhere Korrosionsresistenz. Das NiroSan®-Presssystem ist geprüft nach den DVGW-Arbeitsblättern GW 541 und W 534 und zugelassen von DVGW, ÖVGW, SVGW sowie allen namhaften europäischen Zertifizierungsstellen. Die NiroSan®-Serie 9000 ist auch in einer speziellen LABS*- und silikonfreien Ausführung mit EPDM-Dichtring und in einer separaten Verpackung erhältlich. O ring:EPDM Operating pressure:16 bar Operating temperature:-30 - 120 °C Dimension:15 - 108 mm

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

The innovative SANHA installation system NiroTherm® combines high-quality NiroTherm® press fittings with a black sealing ring made from EPDM (=ethylene propylene diem rubber) and NiroTherm® stainless steel system tubes. The system is produced from the material 1.4301 (AISI 304). Due to the well-known corrosion resistance of stainless steel, NiroTherm® offers installers therefore a real alternative compared to conventional steels when it comes to closed systems in humid atmospheres such as screed. Since it needs considerably less isolation against humidity*, the installation is faster and labour costs accordingly lower. In addition to the system description, NiroTherm® system press fittings are marked on the outside with a red dot. * This does not affect thermal insulation necessitated by national energy efficiency laws. NiroTherm® system pipe, material no. 1.4301, reduced wall thickness, in 6 m lengths, for cooling, compressed air, heating and industrial applications

Das Rohrleitungssystem NiroSan® Gas besteht aus hochwertigen Pressfittings mit einer Formteildichtung aus HNBR und NiroSan®-Edelstahlrohren nach DVGW-Arbeitsblatt GW 541 bzw. DIN EN 10312. Alle NiroSan® Gas Pressfittings werden aus den Werkstoffen 1.4404/316L und 1.4408 gefertigt. Der Werkstoff 1.4404 enthält mindestens 2,3 % Molybdän und einen gegenüber 1.4401 reduzierten Kohlenstoffgehalt. Er ist daher nicht nur gleichwertig mit dem konventionellen Werkstoff 1.4401, sondern überzeugt zusätzlich durch seine deutlich höhere Korrosionsresistenz. Das NiroSan® Gas Rohrleitungssystem für Gase nach DVGW G 260 und für Inneninstallationen nach DVGW G 600 (TRGI) bzw. DVFG-TRF 2012 sind geprüft nach den DVGW-Arbeitsblättern G 260 und G 5614 und sind zugelassen von DVGW, ÖVGW, SVGW sowie allen namhaften europäischen Zertifizierungsstellen. NiroSan® Gas Pressfittings mit gelber Formteildichtung aus HNBR sind außen mit einem gelben „GT-PN 1 (89 mm) bzw. GT-PN 5“ gekennzeichnet. Werkstoff:Edelstahl 1.4404 (AISI 316) Dichtring:HNBR Betriebsdruck:5 bar Betriebstemperatur:-20 - 75 °C Dimension:15 - 108 mm

Rohrleitungssystem aus hochwertigen NiroSan®-Pressfittings (Edelstahlfittings) mit einer Formteildichtung aus EPDM (Ethylen-Propylen-Dien-Kautschuk) und NiroSan®-Edelstahl-Rohren nach DVGW-Arbeitsblatt GW 541 bzw. DIN EN 10312. Alle NiroSan®-Edelstahlfittings werden aus den Werkstoffen 1.4404 / AISI 316L (Formteile aus Edelstahl) und 1.4408 (Gewindeteile, Edelstahl-Feinguss) gefertigt. Der Werkstoff enthält mindestens 2,3 % Molybdän und weist einen geringeren Kohlenstoffanteil als der konventionelle Werkstoff 1.4401 auf. Damit ist er nicht nur gleichwertig zu diesem Edelstahl, sondern überzeugt durch seine deutlich höhere Korrosionsresistenz. Das NiroSan®-Presssystem ist geprüft nach den DVGW-Arbeitsblättern GW 541 und W 534 und zugelassen von DVGW, ÖVGW, SVGW sowie allen namhaften europäischen Zertifizierungsstellen. Die NiroSan®-Serie 9000 ist auch in einer speziellen LABS*- und silikonfreien Ausführung mit EPDM-Dichtring und in einer separaten Verpackung erhältlich.

Das Rohrleitungssystem NiroTherm® besteht aus hochwertigen NiroTherm®-Edelstahl-Pressfittings mit einer schwarzen Formteildichtung aus EPDM (Ethylen-Propylen-Dien-Kautschuk) und NiroTherm®-Edelstahlrohren. Das System - Edelstahl-Pressfittings wie Rohre - wird aus dem Werkstoff-Nr. 1.4301 gefertigt. NiroTherm® bietet Verarbeitern somit eine echte Alternative zu geschlossenen Systemen aus herkömmlichen Werkstoffen, beispielsweise C-Stahl, mit der sich oftmals hohe Arbeitskosten für eine aufwendige Isolierung gegen Feuchte einsparen lassen. NiroTherm® Edelstahl-Pressfittings sind außen zusätzlich zur Systembezeichnung durch einen roten Punkt gekennzeichnet und lassen sich so auch auf der Baustelle gut von anderen Fittings unterscheiden. Hochwertige Edelstahl-Pressfittings und Edelstahlrohre 1.4301 (AISI 304), EPDM

A positive-locking mechanical connection between the cus-tomer’s shaft and the sensor shaft ensures that the magnet in the sensor shaft precisely reflects the rotation of the cus-tomer’s shaft. With the TBN model, one rotation (i.e. max. 16,384 steps) is recorded.With the subsequent absolute transmission, the TRN shaft encoder reaches a measuring range of up to 4096 rotations. The position and speed values (PDO - Process Data Object) are output via the CANopen protocol. Inkremental or absolute:Absolute Interface:CANopen Single- or Multiturn:Singleturn Design:42mm Flange and shaft:Synchro flange, shaft 6mm Housing material:Aluminium 3.2315, Stainless steel 1.4305, Stainless steel 1.4404 Resolution:4096 steps/revolution 12-bit, 8192 steps/revolution 13-bit, 16384 steps/revolution 14-bit Code type:Binary Profile:Standard CANopen C3, Profil No. 4.0.2 Electrical connection:Cable, 1m, axial (other lengths on request), Cable, 1m, radial (other lengths on request)

Robustes Gehäuse aus Aluminium oder nicht-rostendem Stahl - Welle und Kugellager mit Wellendichtring - Rotor mit Welle und Permanentmagnet in Vorkammer gelagert - Sensorschaltung bestehend aus ASICs mit Hall-Elementen und Schnittstellen-Elektronik in geschlossener Hauptkammer untergebracht - Für Schutzart IP 69K ist das Gehäuse zusätzlich vergossen - Elektrischer Anschluss mit Kabel (offene Kabelenden mit Prüfstecker). Inkremental oder absolut:Absolut Schnittstelle:SSI Single- oder Multiturn:Singleturn Bauform:42mm Gehäusematerial:Aluminium, Edelstahl Flansch und Welle:Synchroflansch Auflösung:4096 Schritte/360°<) Codeart:Binär, Gray (optional) Elektrischer Anschluss:Kabel 1m