Produse pentru pour adânc epoxid (40)

COMPOSITION ET ASPECT Blanche. CONDITIONNEMENTS Cartouche de 290 ml. STOCKAGE 12 mois à l’abri du froid et des fortes chaleurs en emballage d’origine non entamé. CARACTÉRISTIQUES TECHNIQUES • Matières premières : MS Polymère • Système de durcissement : par l’humidité • V itesse de durcissement : 2,5 à 3 mm par 24 h. (à T=23°C et 50 % HR) • Formation de peau : 10 à 15 minutes (à T = 23°C et 50 % HR) PRÉCAUTIONS D’EMPLOI Ne pas travailler en dessous de +5°C. Conserver hors de portée des enfants. Contient : N-(3-(trimethoxysilyl)propyl)ethylenediamine - Bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacaat - Methyl1,2,2,6,6-pentamethyl-4-piperidyl sebacaat. Peut déclencher une réaction allergique. PRÉPARATION DES SUPPORTS Les supports doivent être propres, secs, dépoussiérés et dégraissés. APPLICATION Appliquer la colle en extrudant un cordon ou des points sur le support ou l’élément à coller. Assembler les matériaux le plus vite possible : maxi 10 minutes. • Poids spécifique...

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

Unsere Eigenmarke S-Polybond ABSprofi ist ein spezieller ABS Kleber, zum verkleben von ABS, ASA, Polyformage und Polyformage Plus im Kaltschweißverfahren.

Colle de contact transparente à base polyuréthane - spécial PVC doux Pour double encollage de matériaux divers, durs ou flexibles, comme la plupart des matières synthétiques (PVC souple, PVC, ABS, plexi, polycarbonate), bois, panneaux de revêtements décoratifs stratifiés, placage et collage sur champ, nez de marches et marches d’escalier, plinthes en PVC, cuir, liège, textile, métaux entre eux ou sur bois, pierre, béton, plâtre, métal et autres supports lisses et non poreux. Spécifiquement pour des applications dont la couche de colle ou le joint de colle reste visible : comme le collage sur verre ou plexi. Aussi idéal pour la réparation de bâches, toiles de tente et pour matériaux gonflables en PVC souple. Prête à l'emploi, transparente au séchage, pas de trace brune, utilisation aisée à la brosse et au peigne à colle, force d'adhérence progressive rapide, résistante à l'humidité à la chaleur et au froid (-10°C jusqu'à +70°C) Résiste aux acides légers et bases Sans...

L'IDS EPOXYKLEAN 100 est spécialement formulé pour le nettoyage et le décapage des résines époxy, PU, etc. employées pour le collage et jointoiement de revêtements céramique ou autres supports. Ce produit permet l’élimination des vernis époxy, vernis 2K, revêtement anticorrosion, etc. employés notamment dans l’industrie automobile pour le nettoyage des installations d’application de peintures et résines (pistolet, pompes, buses, zones de préparation, sols, etc.). L’IDS EPOXYKLEAN 100 est une solution neutre qui permet le ramollissement des résines même durcies. Sa formulation est totalement exempte de produits CMR. L’IDS EPOXYKLEAN 100 ne corrode pas les métaux ferreux et non ferreux et n’attaque pas les joints dans leur masse. Produit fabriqué en France.

Pardoseala epoxidica cu granule colorate Emex Quartz - See more at: http://www.e - Pardoseala Epoxidica Decorativa EMEX QUARTZ este un produs profesional, pe baza de rasini epoxidice fara solvent, disponibil intr-o gama infinita de modele obtinute prin inglobarea de granule de cuart sau marmura divers colorate in masa pardoselii. Acest tip de pardoseala se mai numeste si covor epoxidic. Produsul poate inlocui cu succes mozaicul sau gresia, avand in primul rand avantajul aspectului superior, dar fiind si o alternativa mult mai rezistenta atat la utilizare dar si in timp a acestora. Caracteristici principale: - Produs agrementat sanitar; - Aderenta excelenta la suport; - Etalare de exceptie; - Duritate excelenta; - Durabilitate mare; - Rezistenta mare la abraziune; - Rezistenta excelenta la uzura; - Rezistenta mare la agenti corozivi; - Rezistenta mare la hidrocarburi, medii acide sau alcaline.

Das Epoxidharz-System E30RB ist eine 2K Epoxi-Rollbeschichtung mit mittlerer Verarbeitungszeit für hochwertige Boden- und Wandbeschichtungen ähnlich RAL7032 kieselgrau.

Nummer Eins chemicals 2008 Yılından beri Kimya sektöründe edinmiş olduğu tecrübeler ışığında müşterilerine en iyi ürünü ve hizmeti sunma felsefesi ile yola çıkarak İSTANBUL tuzla’da A.O.S.B de Epoksi ve Poliüretan Yapı Sistemleri, Antikorrozif epoksi ve poliüretan çelik konstrüksiyon ürünleri, Ahşap ve Metal tekneler için epoksi ve poliüretan ürünler, Su bazlı polimer esaslı su yalıtım sistemleri İç ve Dış mekanlarda kullanılan kaplama sistemlerine yönelik ürünlerin üretimine devam etmektedir. Firmamız kaliteli üretim kaliteli ürün anlayışı ile Avrupa normlarına uygun laboratuar cihazları ve analiz ekipmanlarına sahip ARGE ve Kalite Kontrol Laboratuvarında konusunda uzman mühendis ve kimyager kadrosu ile günümüz dünyasındaki teknolojik gelişimleri yakından takip ederek ürünlerini sürekli geliştirmekte ve yenilikçi bir anlayış ile çalışmalarını sürdürmektedir.

Utilisation de la résine Coulée Couleur du mélange Blanche Viscosité du mélange à 20 °C > 1 000 CPs

Système époxy transparent. Dureté variable. Facile d'emploi. -> Application Décoration, décoration florale, imitation de liquide, simulation de cours d'eau en maquettes. Couleur : Transparent Ratio mélange : 100/100 Potlife : 70 min à 9h Temps avant démoulage : >48h TG°C : nc Unité de vente : 1 kit de 2kg Minimum de commande : 1 kit

Ein hochglänzender Zweikomponenten-Schlusslack mit lichtechten Pigmenten, auf der Basis gesättigter Polyesterharze. Zeichnet sich durch eine gute Deckung, langanhaltenden Glanz, eine besondere Witterungsbeständigkeit und hohe Abriebfestigkeit aus. Geeignet für Pinsel-, Rollen- und Spritzapplikation.

ADLER PUR-based coatings are modern solvent-based systems that meet the most demanding standards in furniture and interior decoration. The best resistance, both for chemical and mechanical stresses and strains, as well as ease of application and use are the special features of this type of coating system. ADLER offers the best choice of PUR-based coatings for the most diverse types of wood as well as the most varied design concepts. Premium quality and efficient use are always ensured in the process. In this manner, you can meet almost any need or requirement for the surface as desired by your customers.

Le produit MAX PROTECT FLEX est une peinture de ravalement de façade particulièrement élastique qui a été conçue pour permettre l'imperméabilisation de supports faïencés ou micro-fissurés. Cette peinture élastoplastique de très haute qualité a été formulée pour faire face à des conditions climatiques défavorables (façades du littoral) et pour répondre aux demandes des professionnels les plus exigeants. MAX PROTECT FLEX est une peinture en phase aqueuse.

Akrilik reçine esaslı, su bazlı, tek kompenantlı, kullanıma hazır, pozitif su basıncına dayanıklı, kaplama altı Kısmi Elastik su yalıtım malzemesidir. Yarı elastik ► Akrilik Reçine Esaslı, Fırça ve rulo uygulanır. ► Su Bazlı, Düşük sıcaklıklarda bile elastikiyetini korur. ► Tek Bileşenli, Yüksek aderans sağlar. ► Kullanıma Hazır, Kullanıma hazırdır. ► Yarı Elastik ► Düşük Sarfiyatlıdır > Beyaz

SUPER NETTOYANT SOLS LISSES 97.8 des ingrédients d’origine naturelle Idéal nettoyages difficiles – Contact alimentaire Nettoyant sols très concentré, idéal pour le nettoyage difficile des sols cimentés, carrelés ou peints. Convient également pour le décapage d’émulsions autolustrantes. Application manuelle ou en autolaveuse. pH > 12. Formulation sur base végétale. 97,8% du total des ingrédients sont d’origine naturelle. Contact alimentaire (arrêté du 19/12/2013). Réf:I536 Conditionnement:Bidon de 5 L – Carton de 4

Additive der Marke PROFI-CAR helfen Ihnen Motor, Kraftstoff- und Kühlersystem in optimalem Zustand zu halten. • Kraftstoffsparend • Verbrennungsoptimierend • Reinigt und schützt das gesamte Kraftstoffsystem • Schützt Motor und Getriebe und vermindert den Verschleiß • Verbessert die Laufeigenschaften • Schließt kleinere Undichtheiten an Motor und Kühlersystem • Beugt Kühlerschäden vor • Verbessert das Umweltverhalten

Zwaluw Acryl Anti-Crack is speciaal ontwikkeld om veel voorkomende problemen bij het overschilderen van de acrylaatkit tegen te gaan zoals scheurtjes en verkleuring in de verf. Niet voor niets is Zwaluw Acryl Anti-Crack zo geliefd door de schilders! Zwaluw Acryl Anti-Crack laat zich makkelijk verwerken bij het afdichten van aansluitvoegen van bijvoorbeeld plafonds, raam- & deur kozijnen, plinten, trappen, ornamenten. Door de unieke samenstelling en omdat het product weekmaker vrij is wordt het risico op scheurtjes in de verf tot een minimum beperkt en zal de verf niet verkleuren door weekmaker migratie. Kortom, bespaar tijd en geld en voorkom narige klachten achteraf en gebruik Zwaluw Acryl Anti-Crack

One Side Adhesive for LEATHER'S PRODUCERS The NEOPRENE ONE WAY is a plychloroprene adhesive adapt for LEATHER'S PRODUCERS and GIUNETRIA in particular in the case where you want apply the glue only in a side. Used for the construction of insoles in shoes too. It has high viscosity. High bond strength. CHARACTERISTICS : Viscosity : 2800 +/- 100 cPs Opened Time : 30 - 60 Minutes USING INSTRUCTIONS : Apply an homogeneous coat upon one of the two parts has to be sticked, let it dries for at least 10 - 15 minutes and join the two parts with hands, hammer or with a press. To dilute the PRODUCT, use SOLVENT P or SOLVENT M. The products has to be conserved in the original tins well closed and in a cool and dry place. N.B.: All the indications over reported are without obligation and warranty. PACKAGING : Kg 800 - Kg 200 - Kg 40 - Kg 15 - Kg 9 Kg 4 - Kg 1 .

Dimensions hors tout:  L 229 x P 350 x Ht 242 cm Surface:  8,00 m2 Structure:  résine avec aspect bois, couleur gris brossé  Porte:  L 148,50 x Ht 182,40 cm Toiture:  imitation tuile 3D Equipement:  plancher robuste + 2 fenêtres + un puit de lumière Garantie:  10 ans, possibilité de peindre les parois murales Dimensions hors tout:L 229 x P 350 x Ht 242 cm Surface:8,00 m2 Structure:résine avec aspect bois, couleur gris brossé  Porte:L 148,50 x Ht 182,40 cm Toiture:imitation tuile 3D Equipement:plancher robuste + 2 fenêtres + un puit de lumière Garantie:10 ans, possibilité de peindre les parois murales

INOX adhesion enhancer, also known as tackifier, improves the adhesion of oils and will lead to stringing. They are typically used in saw chain oils or bio-lubricants. The INOX adhesive concentrates are partially biodegradable and meet the requirements of RAL-UZ 178 for the “Blue Angel” eco-label. item number:1460534 packing:250 L

3 kg - 15 kg - 240 kg - 1000 - 1200 kg ambalajlarda sünger yapıştırıcı

Professionelle Reinigungs- und Pflegeprodukte für Schutzwände Bei uns erhalten Sie Spezialprodukte für die richtige Reinigung und Pflege von Acrylglas und anderen transparenten Kunststoffen Antistatischer Kunststoff-Reiniger und Pfleger Messbar antistatisch und pflegend, erzeugt keine Spannungsrisskorrosionen VPE: Sprühflasche á 250 ml (24 St./Karton) oder 500 ml (12 St./Karton) oder im 10-l-Kanister Kunststoff-Intensivreiniger Intensiv reinigendes Spezialmittel zur Beseitigung stärkerer Verschmutzungen. VPE: Sprühflasche á 250 ml Spezial-Tücher für die Kunststoffpflege Fusselfrei, besonders weich und saugfähig. Baumwollmaterial strapazierfähig und waschbar (bis 40 °C), Größe ca. 28 x 24 cm, Stofffarbe: Chamois VPE: 60 Stück/Packung Acrylglas-Polierpaste Zur Entfernung von Kratzern und blinden Stellen. VPE: Tube á 75 ml (92 g) oder á 200 ml (245 g) Tipps zur richtigen Reinigung/Pflege von Acrylglas finden Sie auf unserer Website.

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Protech AC-P Paint based on acrylic resins in aqueous emulsion, for interiors and exteriors, protective lamellar structure which, in addition to having an aesthetic effect, allows maximum filling, transpiration and very high resistance to mechanical and chemical light. The high coverage and expandability make this product extremely easy to apply. The special acrylic resins that compose it allow to obtain a film characterized by a rapid insensitivity to water even during the drying phase, with a consequent reduction of the "snail effect" in the event of atmospheric events. Protective and decorative finish painting of walls, facades, concrete products, plasters, masonry, natural stone, porous substrates in general. For old plasters, pay particular attention to the old pre-existing paints, which must be removed by careful scraping and brushing in order to obtain a healthy and non-friable support; then proceed with the application of Protech Fix AC fixative. When applying on new plasters, it is good practice to insulate the base with acrylic insulator or even better with a white or neutral microemulsion fixative. Avoid windy or cold days when applying. Do not apply on fresh or particularly alkaline substrates, respect a minimum carbonation period of at least four weeks. On large surfaces it is recommended to apply product from the same batch and always proceed wet on wet to avoid signs of recovery. Never operate with temperatures below + 5 ° C. Rainy weather, excessive atmospheric humidity and temperatures below + 8 ° C can greatly compromise drying with the possibility of washing off by rainwater even after several days. . DILUTION (by volume with drinking water) BRUSH 1st COAT: 15% a crossed coat or two coats 12-24 hours apart 2nd COAT: 10%. ROLLER 1st COAT: 10% 2nd COAT: 10%. SPRAY (through specific equipment) 1st COAT: 15/25% 2nd COAT: 15/25%. To avoid filming defects, being resin-based products in aqueous emulsion, the application temperature must be between + 5 ° C and + 35 ° C with relative humidity not higher than 60/70%. Do not apply under the direct action of the sun and wind. Do not apply on fresh or particularly alkaline substrates, respect a minimum drying period of the substrate of at least four weeks. It is also advisable for colored, not to use on large surfaces dyed with different production batches as slight differences between batch and batch are technically possible. Please check the color before application as we will not respond to any disputes regarding the shade of the applied product. From 0.20 to 0.30 liters of Protech AC-P for each square meter of surface to be painted. Pail 14 l

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Bond Plus Adhesive latex based on elastomeric styrene-butadiene rubber and alkaline silicate in aqueous dispersion, flexibilising, reactive, for adhesive grout and to improve adhesion, the behaviour and performance of mortars and plasters. Production of adhesive, deformable, high-protective and waterproofing performance mortars and plasters for civil, hydraulic, industrial works, in urban, marine and mountain atmospheres. Preparation of hydrating solutions to improve the adhesion and performance of premixed mortars and plasters; preparation of adhesive grouts for non-structural construction joints. Anti-dust treatments, reinforcing concrete surfaces. Shake Bond Plus thoroughly in the tank, and dilute it with water as required. Add the prepared solution to the cement (or lime) and aggregates mixture, in the most suitable dosages for this application, as specified below. It is always essential to carry out preliminary tests for an accurate definition of the mixtures to use, and to check the suitability of the product on the basis of the specific requirements. Refer to the table shown in the product datasheet. Packaging: 25 kg can UM: €/kg

Protech Fix AC-Therm Water-based anti-condensing wall covering, with excellent fixing and anchoring properties, with good coverage based on high penetration acrylic resins, 3M Glass Bubble, pigments, fillers and covering fillers. Suitable as an anti-condensation fixative primer, prior to painting or coating the plaster with anti-condensation paints or plasters (-THERM). Ideal for interventions on walls with mucilage deposits, bacterial phenomena and moulds. Due to its low thermal conductivity, it is particularly suitable for solving mould problems. It can be applied on any plaster (rustic, civil, plaster, dry mortar, plasterboard, concrete, prefabricated, exposed concrete, etc.). Made with special resins and additives it reduces the absorption of the support while allowing the necessary transpiration, uniforms the absorption making the application of the finishing coats easier. It always works in depth, which is why it is the ideal preparation for applying water-based paints or coatings. Adhesion is excellent even on particularly difficult surfaces, thanks to the use of special resins and the presence in the formulation of an adhesion promoter interacting between the support and the product. Preliminary treatment of any surface (civil, plaster, rustic, dry mortars, plasterboard, concrete, prefabricated, exposed concrete etc.) designed to isolate the support surfaces and standardise the absorptions of the subsequent anti-condensate treatments (painting and protective coatings). Packaging: 14-liter bucket UM: €/l

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]