Produse pentru pigmenți de ciment (26)

Unisan A composite mortar that is fibre-reinforced, consolidating, dehumidifying, grey in colour and utilised for the structural restoration of crumbling old or monumental masonry. It contains no substances that are potentially harmful to masonry and is composed of NHL 3.5 natural hydraulic lime and hydraulic binders free from soluble salts, along with silicas with pozzolanic activity, selected siliceous-calcareous aggregates, specific shrinkage-reducing agents and resistant alkaline READYMESH fibres that confer high flex-traction whilst increasing the performance of the mortar’s fracture energy. In conjunction with ARMAGLASS STRUCTURA fibreglass mesh, it is ideal for the structural restoration of old walls or crumbling constructions. Construction of plasters and reinforced slabs in interventions of restoration, construction of plaster and dehumidifying coatings with high performance, bedding of bricks and modular elements. The surfaces should be clean and free of any soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition of "saturated dry surface". In the case of structural reinforcing slabs, you will need to proceed with applying an appropriate reinforcing electrowelded mesh, to be fixed with PROFIX, Grout Micro-J, Repar Tix G2 or Syntech IC 55. Pour about 2/3 of the mixing water into the mixer, add Unisan and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 12-14% of the weight of the bag. After mixing is completed wait a few minutes before applying. Apply the product by plastering trowel and brick trowel, or preferably with plastering machine (type PFT model G4). Do not apply in case of direct exposure to sunlight or excessive ventilation. Cure the protection and the prolonged moist hardening, of exposed surfaces. Approximately 15 kg/m² of Unisan for every centimetre of thickness to be implemented (approximately 1500 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

CONDITIONNEMENTS Sacs de 5 kg. STOCKAGE 6 mois en emballage d’origine non entamé à l’abri de l’humidité. PRÉPARATION DES SUPPORTS Les supports doivent être propres, dépoussiérés, durs et exempts de toute trace d’agent séparateur. Les supports très poreux ou par temps chaud devront être préalablement humidifiés. TAUX DE GÂCHAGE PÂTE PURE : 1 volume d’eau pour 3 volumes de ciment. MORTIER : 1 volume d’eau, 7 volumes de sable et 3 volumes de ciment. BARBOTINE : 1 volume d’eau pour 2 volumes de ciment.

SOLVENT PAINT of COSMOCHROME is a high quality undercoat for concrete surfaces (concrete columns, concrete floors, walls, ceramic tile roofs etc). It is highly durable against extreme weather conditions and atmosphere pollution. It has strong adhesion, great covering power and extreme hardness PACKAGE:0,75 LT, 10 LT, 2,5 LT COLOR:Black, Cypress Green

30-35% CaO 15-18% MgO

Diamantpulver für Polituren und Abtrag - hochwertige Klassierungen ausgewählter Kornqualitäten für beste Abtragsleistungen bei kratzerfreien Oberflächen - auf Basis langjähriger Erfahrungen ausgewählter Korntypen für die Bearbeitung weicher, harter, sprödharter und kristalliner Materialien

Mineral Plus

* It is applied in 2 cm thickness. * 1 package of product is 20 kg. 1.6-1.8 kg of product is required for 1 m2 area. * You can easily reach an application area of ​​12 m2 by using a 20 kg Multiyap and a 6 mm notched trowel. * By providing waterproofing, even if the joint fillings between the tiles deteriorate, water does not leak to the lower floor. * There is no need to make water isolation in bathroom applications. * Since it is a hydrophobic product, a single product provides both water isolation and a strong tile ceramic application with superior performance. * It is quite light. It reduces labor and transportation costs. * It is flexible and the working time is extended. * It has strong adhesion feature.

Rapid Set CONCRETE MIX ist ein auf BCSA-Zementtechnologie basierender, mineralischer, multi-funktionaler Schnellreparaturmörtel für Schichtdicken von 50 - 600 mm. Geeignet für Betoninstandsetzung, Reparatur und Bau von Gehwegen, Fahrbahnen, Beton- und Maschinenfundamente, Schalungsarbeiten sowie Industrieböden, für innen und außen, auch in Nassbereichen. Erstarrungsbeginn nach ca. 15 Minuten, belastbar nach ca. 1 Stunde. Eigenschaften:für Reparatur und Neubau horizontal und vertikal spannungsarm Lieferform:25 kg Papierspezialverpackung

CBG-DP-90 is a dense, refractory, self-flowing concrete with low cement content intended for use in aggressive environments, including contact with molten metals and slags at temperatures up to 1,900°C, especially for the production of monolithic linings of steel ladles, elements of the metal tract and as a repair concrete mass. It can be used for monolithic linings as well as for products of any configuration and complexity. — high temperature resistance — high temperature of liquid phase formation — high mechanical strength — high temperature of onset of deformation under load — does not contain substances that cause allergic reactions — resistant to molten metal, acid and alkaline slags Main application: ferrous, non-ferrous and glass industry, lining of melting aggregates in the production of mineral fibres etc.

Oksit Sarı Gübre Boyası / Oxide Yellow Fertilizer Paint

Kundenspezifische Pigmentmischungen für die Profilextrusion, Spritzgussanwendungen und für die Compound-Herstellung. Viele unsere Kunden greifen heute auf unsere Pigmentpräparationen zurück, da diese eine kostengünstige Alternative zu Masterbatches bei der Einfärbung von Kunststofferzeugnissen darstellen. Diese Farbkonzentrate sind besonders gut geeignet und eine preisgünstige Alternative für Compoundhersteller die keine eigene Coloristikabteilung in Ihrem Unternehmen aufbauen wollen. Kundenspezifische Farbeinstellungen sind bereits ab 25 kg Abnahme möglich. Produktgruppen: DEI®ART Künstler Pigmente

Wir sind Ihr Partner für individuelle Pulverbeschichtung.

Als Service-Partner der Schüttgut verarbeitenden Industrie, entwickeln und realisieren wir mit Ihnen Ihr individuelles Projekt im Bereich Granulierung und Kompaktierung. Die Herstellung und Verarbeitung von Granulaten bietet eine Reihe von Vorteilen gegenüber dem Einsatz nicht-granulierter Feststoffe: So weisen Granulate eine verbesserte Fließ- und Haftfähigkeit auf, vorteilhaft beim Verpressen zu Tabletten. Die Gleichmäßigkeit der Granulate ermöglicht eine höhere Dosiergenauigkeit und die homogene Verteilung der Wirkstoffe. Da sich nicht alle Rohstoffe in trockenem Zustand optimal verarbeiten lassen, bieten wir unseren Kunden auch für diesen Fall die passende Lösung: Die Feuchtgranulation.

Zum Einsatz an Polier-, Lappenscheiben und Bürsten. Die Blöcke werden an die rotierenden Scheiben gedrückt und erweichen sich an der Oberfläche durch Reibungswärme. Dadurch überträgt sich die Paste auf die Scheibe.

Idropittura minerale antialga a base di silicati di potassio stabilizzato ed idrofobizzato, per la decorazione e protezione interna ed esterna di superfici sia nuove che vecchie, come intonaci base calce e cemento, intonaci base calce, intonaci deumidificanti, intonaci idrorepellenti, finiture minerali, intonaci a cappotto premiscelati, calcestruzzo. Elevatissima copertura, sicura inalterabilità agli agenti atmosferici ed ai raggi ultravioletti. Possiede caratteristiche di alta traspirabilità (infatti compatibile con sistema deumidificante) e allo stesso tempo caratteristiche di idrorepellenza. COLORE: Bianco e colori cartella CONFEZIONE: Fusto 4 - 14 lt UTILIZZO: Interno/Esterno DILUIZIONE: Pronto all'uso RESA: 7/8 mq/lt per mano COEFF. DI ASSORB. D'ACQUA CAPILLARE “W24”: < 0,10 kg/(mq*24 h½) RESISTENZA ALLA DIFFUSIONE DEL VAPORE m EQUIVALENTI “Sd”: = 0,08 m TEORIA DI KUENZLE “W*Sd”: < 0,01 kg/(mq*24 h½) CONFORME ALLA DIN 18363

Simon monokristalles synthetisches Diamantpulver wird überwiegend zur nassen und trockenen Endbearbeitung von Hartmetallwerkzeugen verwendet. Natürlich aber auch für alle NE-Metalle.

PDM granül kauçuktan üretildiği için oldukça esnek bir maddedir. Bu nedenler her türlü şarta kolaylıkla ayak uydurabilir. Yazın güneşi ya da kışın soğuğu bu malzemeye hiçbir şekilde zarar veremez. Elastik olmasından dolayı darbelere karşı oldukça fazla dayanıklıdır. Elastik olması malzemenin her şekle girmesine de yardımcı olur. Yapısı gereği çok dayanıklı bir ürün olan EPDM granül, öyle hava şartlarına göre değişiklik göstermez. Her duruma dayanıklı olan bu malzemede esneme, genleşme, büzülme gibi olaylar asla yaşanmaz. Bu sayede yaz sıcağında ve kış soğuğunda kolaylıkla kullanılır. EPDM sonradan renklendirilen bir madde değildir. Boyama yöntemi kullanılmayan bu malzemede renk solması gibi bir durum asla yaşanmaz. Yıllarca renkleri bozulmadan kalabilir. Bu malzemede aklınıza gelebilecek her rengi kullanabilirsiniz. Geniş bir renk seçeneğine sahip olan EPDM granül size istediğiniz rengi seçme şansını verecektir.

There are 6 types of dry pressing ferrite powder for customers: YXC-C1, YXC-C2T, YXC-C3T, YXC-C1, YXC-C2. The procedure summaries for making magnet are as follows: •The necessary secondary additives have been added into the powder during the grinding process. Customers only need to add proper quantity of binders and lubricants. The powder must pass through 120 mesh sieve before pressing, so as binders to be uniformly distributed for better orientaton •Please take care of the cleaning of the equipments. Any other materials and impurity should mot be mixed into the powder •During pressing, the pressure required is ≥5000N/cm2, and the magnetic field density is >7000 Oe(560KA/m) •The sintering temperature for reference is between 1220 °C and 1270 °C. Please note that the proper sintering temperature should be defined in accordance with the status of the sintered sample pill Material:ferrite magnet Size:can be customized package:as required

Pour l’agglomération du minerai de fer, ces castines sont constituées de calcaire à plus de 97% de carbonate de calcium. Elles servent également de composant dans les engrais. Contactez-nous pour des informations complémentaires

DÉFINITION TECHNIQUE Enduit de réparation intérieur et extérieur sans retrait, à haut pouvoir adhésif. • Rebouche : trous et fissures, joints sur briques, béton cellulaire • Répare : corniches, angles de fenêtres • Scelle : gonds et pitons • Enduit : façade, crépi, parpaing... COMPOSITION ET ASPECT Enduit en poudre à base de ciment, sable, résine et divers adjuvants. La pâte obtenue est de couleur grise. SUPPORTS ADMIS Tous types de supports propres, sains, secs, dépoussiérés et exempts de toute trace d’huile : maçonnerie, béton, enduit ciment. REVÊTEMENTS Le recouvrement, après séchage complet de l’enduit, peut se faire par tous types de peintures, enduits à base de plâtre, enduits pâteux, enduit ciment, RPE. DOCUMENTS À CONSULTER DTU 42.1. CARACTÉRISTIQUES TECHNIQUES • Granulométrie : fine • Adhérence : conforme au DTU 42.1 • pH : alcalin. Début de prise : 40 minutes • Fin de prise : 1 h 30 CONDITIONNEMENTS Sacs de 5 et 15 kg sur palette houssée. STOCKAGE 6 mois...

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

COMPOSITION ET ASPECT Ciment spécial, sable et divers adjuvants. La pâte est de couleur foncée. SUPPORTS ADMIS • Béton • Brique en terre cuit • Brique réfractaire DOCUMENTS À CONSULTER DTU 20.1 et DTU 24.1. CARACTÉRISTIQUES TECHNIQUES • Temps de prise : 30 mn • Température admise après séchage complet : 1000 °C CONDITIONNEMENTS Sacs de 5 et 25 kg sur palette houssée. STOCKAGE 6 mois en emballage d’origine non entamé à l’abri de l’humidité. PRÉPARATION DES SUPPORTS Les supports doivent être propres, dépoussiérés, durs et exempts de toute trace d’agents séparateurs. Les supports très poreux ou par temps chaud devront être préalablement humidifiés. TAUX DE GÂCHAGE Environ 3 à 4 l. d’eau par sac de 25 kg. APPLICATION Appliquer à l’aide d’une truelle à maçonner puis d’un fer à joints. Entre deux briques, créer un joint d’environ 1 cm et en retrait de 5 à 7 mm par rapport aux bords.

ESCRIPTION Enduit pour reboucher rapidement les fissures, trous et saignées de toutes tailles sans retrait et sans fissuration. COMPOSITION ET ASPECT Enduit en poudre à base de plâtre, carbonate de calcium, charge minérale, cellulose et divers adjuvants. La pâte obtenue est de couleur blanche. SUPPORTS ADMIS Tous types de supports en intérieur bruts ou peints : plâtre, plaques de plâtre, carreaux de plâtre, béton, enduit ciment, agglos, béton cellulaire, briques, terre cuite… CARACTÉRISTIQUES TECHNIQUES • pH : neutre • Temps de prise : 30 minutes en fonction des conditions ambiantes et de l’épaisseur appliquée CONDITIONNEMENT Sacs de 5 et 15 kg. APPLICATION L’application se fait au couteau à enduire. Consommation : 1kg /m²/mm d’épaisseur. TEMPS DE SÉCHAGE Il dépend des conditions ambiantes, de la nature du support et de l’épaisseur d’application. En règle générale, pour un cm d’épaisseur, l’enduit est sec en 6 heures.

CBG-DP-90 ist ein dichter, feuerfester, selbstfließender Beton mit niedrigem Zementgehalt, der für den Einsatz in aggressiven Umgebungen, einschließlich Kontakt mit geschmolzenen Metallen und Schlacken bei Temperaturen von bis zu 1.900°C, insbesondere für die Herstellung von monolithischen Auskleidungen von Stahlpfannen, Elementen des Metalltrakts und als Reparaturbetonmasse bestimmt ist. Er kann sowohl für monolithische Auskleidungen als auch für Produkte beliebiger Konfiguration und Komplexität verwendet werden. — hohe Temperaturbeständigkeit — hohe Temperatur der Flüssigphaseentstehung — hohe mechanische Belastbarkeit — hohe Temperatur beim Einsetzen der Verformung unter Last — enthält keine Stoffe, die allergische Reaktionen hervorrufen — beständig gegen Metallschmelze, saure und alkalische Schlacken Hauptanwendung: Eisen-, Nichteisen- und Glasindustrie, Auskleidung von Schmelzaggregaten bei Herstellung von Mineralfasern etc. Zusammensetzung:Korund, Tabulartonerde, Spinell Bindung:Hydraulisch Anwendungstemperatur:bis zu 1 .900°C Temperaturwechselbeständigkeit:> 40 Wasserabkühlzyklen von 1300°C bis auf Kühlwassertemperatur Temperatur bei Beginn der Verformung unter Last 0,2 MPa:1 .850°С Dichte:2.850 kg/m³ Maximale Korngröße:10 mm Wasserverbrauch:5,0-5,3 l/100 kg Chemische Zusammensetzung:Al2O3 - 88,5 % ; MgO - 0,5 % ; Cr2O3 - 2,5 % ; Fe2O3 - 0,5 % ; CaO - 5,0% Dichte (g/cm³):2,85 (bei Temp. 110 °C) ; 2,85 (bei Temp. 800 °C) ; 2,90 (bei Temp. 1350 °C) Wärmeleitfähigkeit (W/m∙K):1,94 (bei Temp. 110 °C) ; 2,56 (bei Temp. 800 °C) ; 2,70 (bei Temp. 1350 °C) Druckfestigkeit (MPa):85 (bei Temp. 110 °C) ; 80 (bei Temp. 800 °C) ; 110 (bei Temp. 1350 °C) Restliche lineare Deformation (%):0 (bei Temp. 110 °C) ; 0 (bei Temp. 800 °C) ; -0,1 (bei Temp. 1350 °C) Offene Porosität (%):n.a. (bei Temp. 110 °C) ; 16,0 (bei Temp. 800 °C) ; 14,9 (bei Temp. 1350 °C)

Anti-algae mineral paint based on stabilised potassium silicates for the interior and exterior decoration and protection of both new and old surfaces, such as lime and cement plasters, lime base plasters, dehumidifiers plasters, Water-repellent plasters, mineral finishes, pre-mixed coat plasters, concrete. Very high coverage, safe non-reactivity to atmospheric agents and ultraviolet rays. It has characteristics of high breathability (in fact compatible with dehumidifying systems) and at the same time characteristics of water repellency.