Produse pentru pigmenți de ciment (13)

Unisan A composite mortar that is fibre-reinforced, consolidating, dehumidifying, grey in colour and utilised for the structural restoration of crumbling old or monumental masonry. It contains no substances that are potentially harmful to masonry and is composed of NHL 3.5 natural hydraulic lime and hydraulic binders free from soluble salts, along with silicas with pozzolanic activity, selected siliceous-calcareous aggregates, specific shrinkage-reducing agents and resistant alkaline READYMESH fibres that confer high flex-traction whilst increasing the performance of the mortar’s fracture energy. In conjunction with ARMAGLASS STRUCTURA fibreglass mesh, it is ideal for the structural restoration of old walls or crumbling constructions. Construction of plasters and reinforced slabs in interventions of restoration, construction of plaster and dehumidifying coatings with high performance, bedding of bricks and modular elements. The surfaces should be clean and free of any soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition of "saturated dry surface". In the case of structural reinforcing slabs, you will need to proceed with applying an appropriate reinforcing electrowelded mesh, to be fixed with PROFIX, Grout Micro-J, Repar Tix G2 or Syntech IC 55. Pour about 2/3 of the mixing water into the mixer, add Unisan and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 12-14% of the weight of the bag. After mixing is completed wait a few minutes before applying. Apply the product by plastering trowel and brick trowel, or preferably with plastering machine (type PFT model G4). Do not apply in case of direct exposure to sunlight or excessive ventilation. Cure the protection and the prolonged moist hardening, of exposed surfaces. Approximately 15 kg/m² of Unisan for every centimetre of thickness to be implemented (approximately 1500 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

CONDITIONNEMENTS Sacs de 5 kg. STOCKAGE 6 mois en emballage d’origine non entamé à l’abri de l’humidité. PRÉPARATION DES SUPPORTS Les supports doivent être propres, dépoussiérés, durs et exempts de toute trace d’agent séparateur. Les supports très poreux ou par temps chaud devront être préalablement humidifiés. TAUX DE GÂCHAGE PÂTE PURE : 1 volume d’eau pour 3 volumes de ciment. MORTIER : 1 volume d’eau, 7 volumes de sable et 3 volumes de ciment. BARBOTINE : 1 volume d’eau pour 2 volumes de ciment.

SOLVENT PAINT of COSMOCHROME is a high quality undercoat for concrete surfaces (concrete columns, concrete floors, walls, ceramic tile roofs etc). It is highly durable against extreme weather conditions and atmosphere pollution. It has strong adhesion, great covering power and extreme hardness PACKAGE:0,75 LT, 10 LT, 2,5 LT COLOR:Black, Cypress Green

Mineral Plus

Permeat jest produkowany ze świeżego pasteryzowanego odtłuszczonego mleka, powstałego po ultrafiltracji mleka w celu ekstrakcji białek i tłuszczów. Produkt jest następnie suszony przy użyciu zaawansowanych technik suszenia rozpyłowego. Produkt jest czasem nazywany „serwatką odbiałczoną”, gdy jest uzyskiwany z serwatki. Dzięki temu, że permeat serwatki jest bogaty w laktozę, ale ma niską zawartość białka, może być stosowany do produkcji słodyczy, wyrobów piekarniczych i tłuszczów. Dodawany jest również do produkcji lodów, serów topionych, napojów i kosmetyków.

Titandioxide der Cofermin Chemicals, Essen, Deutschland in diversen Qualitäten (Anatas und Rutil) Herkunft:Deutschland

Als Service-Partner der Schüttgut verarbeitenden Industrie, entwickeln und realisieren wir mit Ihnen Ihr individuelles Projekt im Bereich Granulierung und Kompaktierung. Die Herstellung und Verarbeitung von Granulaten bietet eine Reihe von Vorteilen gegenüber dem Einsatz nicht-granulierter Feststoffe: So weisen Granulate eine verbesserte Fließ- und Haftfähigkeit auf, vorteilhaft beim Verpressen zu Tabletten. Die Gleichmäßigkeit der Granulate ermöglicht eine höhere Dosiergenauigkeit und die homogene Verteilung der Wirkstoffe. Da sich nicht alle Rohstoffe in trockenem Zustand optimal verarbeiten lassen, bieten wir unseren Kunden auch für diesen Fall die passende Lösung: Die Feuchtgranulation.

Acteur de vos domaines: Sourcing matiére premiére Cosmetic Santé et bien etre Le magnésium marin sous forme sèche en poudre peut s’utiliser en complémentation alimentaire pour pallier aux carences et lutter contre le stress et la fatigue. L’oxyde de magnésium marin est extrait de notre eau de mer. Sa grande pureté garantie sa forte teneur en magnésium. L’eau de mer est deposée dans des marais salants pour obtenir une évaporation naturelle et concentrer l’eau en minéraux. Cette eau est ensuite plasée dans une tour d’atomisation afin d'evaporer l'eau et pour ne garder que le concentré minéral. La teneur de notre concentré minéral est à hauteur de 85 %.

DÉFINITION TECHNIQUE Enduit de réparation intérieur et extérieur sans retrait, à haut pouvoir adhésif. • Rebouche : trous et fissures, joints sur briques, béton cellulaire • Répare : corniches, angles de fenêtres • Scelle : gonds et pitons • Enduit : façade, crépi, parpaing... COMPOSITION ET ASPECT Enduit en poudre à base de ciment, sable, résine et divers adjuvants. La pâte obtenue est de couleur grise. SUPPORTS ADMIS Tous types de supports propres, sains, secs, dépoussiérés et exempts de toute trace d’huile : maçonnerie, béton, enduit ciment. REVÊTEMENTS Le recouvrement, après séchage complet de l’enduit, peut se faire par tous types de peintures, enduits à base de plâtre, enduits pâteux, enduit ciment, RPE. DOCUMENTS À CONSULTER DTU 42.1. CARACTÉRISTIQUES TECHNIQUES • Granulométrie : fine • Adhérence : conforme au DTU 42.1 • pH : alcalin. Début de prise : 40 minutes • Fin de prise : 1 h 30 CONDITIONNEMENTS Sacs de 5 et 15 kg sur palette houssée. STOCKAGE 6 mois...

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

COMPOSITION ET ASPECT Ciment spécial, sable et divers adjuvants. La pâte est de couleur foncée. SUPPORTS ADMIS • Béton • Brique en terre cuit • Brique réfractaire DOCUMENTS À CONSULTER DTU 20.1 et DTU 24.1. CARACTÉRISTIQUES TECHNIQUES • Temps de prise : 30 mn • Température admise après séchage complet : 1000 °C CONDITIONNEMENTS Sacs de 5 et 25 kg sur palette houssée. STOCKAGE 6 mois en emballage d’origine non entamé à l’abri de l’humidité. PRÉPARATION DES SUPPORTS Les supports doivent être propres, dépoussiérés, durs et exempts de toute trace d’agents séparateurs. Les supports très poreux ou par temps chaud devront être préalablement humidifiés. TAUX DE GÂCHAGE Environ 3 à 4 l. d’eau par sac de 25 kg. APPLICATION Appliquer à l’aide d’une truelle à maçonner puis d’un fer à joints. Entre deux briques, créer un joint d’environ 1 cm et en retrait de 5 à 7 mm par rapport aux bords.

ESCRIPTION Enduit pour reboucher rapidement les fissures, trous et saignées de toutes tailles sans retrait et sans fissuration. COMPOSITION ET ASPECT Enduit en poudre à base de plâtre, carbonate de calcium, charge minérale, cellulose et divers adjuvants. La pâte obtenue est de couleur blanche. SUPPORTS ADMIS Tous types de supports en intérieur bruts ou peints : plâtre, plaques de plâtre, carreaux de plâtre, béton, enduit ciment, agglos, béton cellulaire, briques, terre cuite… CARACTÉRISTIQUES TECHNIQUES • pH : neutre • Temps de prise : 30 minutes en fonction des conditions ambiantes et de l’épaisseur appliquée CONDITIONNEMENT Sacs de 5 et 15 kg. APPLICATION L’application se fait au couteau à enduire. Consommation : 1kg /m²/mm d’épaisseur. TEMPS DE SÉCHAGE Il dépend des conditions ambiantes, de la nature du support et de l’épaisseur d’application. En règle générale, pour un cm d’épaisseur, l’enduit est sec en 6 heures.