Produse pentru magnet din (1618)

Pneumatically actuated magnetic gripper type PNEUMAG are pneumatic switchable bi-stable magnetic systems. Air pressure is only needed for switching. The magnet system is permanent and thus keeps safe even with pressure drop. PNEUMAG magnetic grippers enable thin, perforated or textured sheet metal parts (from 0,5mm) take and safe to transport what they recommended specifically for use in automatic and semi-automatic feeding systems as well as slings for robot grippers. PNEUMAG is the alternative to vacuum conveying systems. They were tested on a metal sheet St37 with smooth and clean surface. Note that depending on the application a safety factor of 2 or 3 has to be included.

The above mentioned filter bars are our standard designs. Here the end pieces are not sealed tight and therefore only suitable for dry applications. Not available ex stock, manufactured on demand. Alternative to the standard we also offer individual solutions: » Seal-welded model for use in liquids (e.g. water, coolant) » High-quality stainless steel enclosure for use in food production » Increasing the max. operating temperature up to 350 °C » Manufacture of individual, not standardised sizes Article number:MS100NdSo00rh00 D mm:100 H mm:40 Temperature °C:80 Diameter of filter bars:25

The MCF control units are designed to operate electro-permanent magnet modules. It is available both as a single board for installation in the customer's existing control cabinets and as an IP 54 control cabinet solution. In addition to the FXE lifting magnet modules, other electro-permanent magnet components such as magnet clamping plates or magnet clamping blocks can also be controlled with the MCF, both as a single system (ALNICO) and as a double system (ALNICO/ND). The MCF can be controlled via a machine control, radio remote control, manual pushbutton or other potential-free contacts.

FXL-CT table-top units are built for a maximum of 2 channels without preselection. They can be used to control magnetic chucks up to a total area of approx. 1.2m2. can be controlled. FXL-CT is designed as a table-top unit or to be attached to the machine wall by means of the magnetic feet on the back. The operation is carried out directly on the device.

Test equipment for magnetic fields Article number:MagFeldFolie Note:film for showing the magnetization

Our rubber caps are used as scratch protection especially on delicate surfaces. They can be used with our flat pot and decoration magnets in order to protect the surface. Moreover it lowers the noise when putting on the magnet. Article number:GU-16 D mm:16 h mm:0.5

Umpolsteuergeräte aus der FXL-C Familie steuern nicht nur zuverlässig unsere FXL Magnetspannplatten, sondern nahezu alle am Markt befindlichen Elektro-Permanent Magnetsysteme. Eingangsspannungen von 100-500 VAC / 50-60Hz und dazu passend modulierte, gepulste Ausgangsspannungen und Impulsleistungen von bis zu 24 kVA sind einzigartige Eckdaten, welche nur unter extremen Bedingungen gefordert sind, aber im normalen Einsatz für maximale Stabilität sorgen. FXL-C gibt es vom einfachen, handlichen Tischgerät bis hin zur Schaltschrankversion für Großanwendungen; autark von handbedient, teilegebunden mit Rückmeldung an die Maschine bis hin zur Volleinbindung in die Maschinensteuerung für automatisierte Anwendungen.

Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material) Article number:F6-SCAv D mm:6 +0.1/ -0.1 d mm:6 +0.1/ -0.1 H mm:4.5 +0.1/ -0.1 L mm:11.5 +0.2/ -0.2 Thread M:M3 Temperature °C:200

The HGF Handgausmeter is an easy to use precision instrument. The superfine 1mm probe magnetic flux densities can be measured extremely close to the magnetic pole and in very narrow air gaps. The HGF can be switched between AC and DC magnetic fields as well as between units Gaus and Tesla. At the edge of the display the pending polarity N/S is in the mode "DC magnetic fields" constantly displayed, the "peak indicator" facilitates the search for magnetic surfaces for example, in tracking down unwanted residual magnetism. The package includes in addition to the meter, the 1mm transversal probe and the batteries and a protective case and a protective cap for the probe. Thus, HGF is also suitable for use in the service industry. Our technicians use it for testing of heavy lifting magnets and clamping systems.

MBX magnetic clamping blocks have opposite clamping sides that are activated when actuated. They are designed to clamp workpieces on steel surfaces such as machine or assembly tables. Several MBX can also be connected together via the internal hexagon of the indexing shaft to clamp longer or larger workpieces.

The PP1 chips collector is used for the rapid collection of shavings and other metal parts, for cleaning the workplace, the machine or for the collection of metal parts from waste or ash. The collected metal parts can be removed by pulling the rear release button. Magnets for surface and railing cleaning clean halls and outdoor areas from magnetic parts and thus protect personnel and equipment

Smco Magnet

Neodymium magnet (aka NdFeB magnet), is the third generation of rare earth magnet, which is composed of Neodymium, Iron, Boron and a few transition metals. With high remanence, high coercive force, high energy product, and high performance /cost, Neodymium magnet is currently the strongest magnet available in the world. Manufacturing Process Neodymium, Iron, Boron and a few transition metals will be mixed into the Neodymium powder, then fine Neodymium powder will be compacted in a die and sintered, fusing the powder in a solid state. There are two ways of pressing die pressing and isostatic pressing. Sintered parts normally need some finish machining in order to meet final tolerances. Machining & Tolerance Generally, Neodymium magnet must be machined using diamondgrinding techniques. Sometimes, machining operations may be performed on Neodymium materials with carbide tools, but surface finishes thus obtained may be less than optimal.

Smco Magnet

Smco Magnet

Smco Magnet

Smco Magnet

Smco Magnet

Smco Magnet

Bonded Ndfeb Magnet

Fits any style cabinet door Strong magnetic force Plastic parts surface to avoid corrosion Prevents the cabinet or cupboard doors from hitting the wall while opening Easy installation Fasteners could be provided

Magnetic Name Badge is a commonly used magnetic product. It is composed of magnets and plastic or metal panels. It is widely used in office environment, hotels, teahouses and other service personnel. The magnetic chest is small and beautiful in appearance, easy to wear and durable

Timone di posizionamento per dirigere e posizionare i magneti di sollevamento SB, EPMB e EPMM. Il timone di posizionamento ha un raggio di orientamento regolabile in continuo di +/- 60°. La regolazione avviene semplicemente rilasciando il freno a mano. Opzionalmente, è possibile montare un radiocomando per la commutazione del magnete direttamente sulla maniglia. Altri telecomandi per il controllo delle gru sono disponibili su richiesta. Timone di posizionamento:N. 70129

The Pivot magnetic welding angle has a holding angle range from 28 to 270 degrees. The Pivot magnetic welding angle is a universal handyman for smaller welding and assembly work on round and flat material. Through the quick release and a scale, the angle can be set simply and precisely. Components can be clamped on the inside or outside. Each leg can be switched on and off through a rotary switch. PA:Item No. 60343

Il Piano Magnetico Elettropermanente brevettato (EPM) con tecnologia a polo quadrato e con superficie interamente in acciaio è la perfetta soluzione per bloccare i pezzi ferromagnetici sulle macchine utensili in modo affidabile ed efficace. Utilizzando le estensioni del polo, le irregolarità del pezzo vengono compensate e la distorsioni del pezzo stesso sono pertanto annullate. 304 HD 75:N. 48900 306 HD 75:N. 49835 308 HD 75:N. 52548 404 HD 75:N. 52546 406 HD 75:N. 49011 408 HD 75:N. 49012 410 HD 75:N. 50235 508 HD 50:N. 52545 510 HD 75:N. 49833 606 HD 75:N. 52543 608 HD 75:N. 52544 610 HD 75:N. 49985

The electropermanent load lifting magnets from the EMPH series are suitable for the lifting and transportation of individual slabs and unprocessed blocks. These magnets are used to handle loads with a large air gap or with scaled surface. Only a 400V rated current must be provided to use these devices and they are then immediately ready for use. Through short electrical impulses within seconds, the EPMH from ASSFALG are automatically switched on or manually with the push of a button. No electricity flows during load transport and nevertheless, the workpiece is as securely clamped as with a permanent load lifting magnet. Through the impulse current control, the EPMH load lifting magnets do not use much energy. The effectiveness and efficiency can be seen on the one hand in the reduction of operating costs and on the other hand in a saving of time. EPMH 10:Item No. 63501 EPMH 15:Item No. 72048 EPMH 20:on request EPMH 25:on request EPMH 30:on request

Die Assfalg Batterie Elektro-Permanent Lasthebemagnettraverse hat eine kompakte Bauform. Durch die integrierte wiederaufladbare Batteriebox ist keine Stromanbindung mehr erforderlich. Das Schalten der EPM Batterie Magnettraverse erfolgt über eine Fernbedienung. Die Lasttraverse mit 1.500 kg max. Traglast ist mit Magnetmodulen ausgestattet und kann damit Blechformate von min. 500 mm Länge bis max. 4000 mm Länge sicher bewegen. Flachlast:1.500 kg mind. Stärke:3 mm Länge min. - max. :500 - 4.000 mm Breite min. - max. :1.000 - 2.000 Gewicht:700 kg Art.-Nr.:75016

Diese Magnetschweißwinkel sind Ihre unentbehrliche dritte Hand bei Schweiß- und Montagearbeiten an Rund- und Flachmaterial. Bei diesen kleinen und handlichen Magnetschweißwinkel können Werkstücke aus Metall bei 45° sowie in 90° gehalten werden. Sie sind robust, wartungsfrei und können bis zu einer Temperatur von 80 °C eingesetzt werden. Werkstücke lassen sich leicht positionieren, ausrichten und fixieren. MSA I:Art. - Nr. 45338 MSA II:Art. - Nr. 45339

Il Piano Magnetico Elettropermanente con tecnologia Assfalg a poli radiali è l’ideale per bloccare pezzi rotazionalmente e pezzi simmetrici senza distorsione fino a 400 mm di diametro. Un foro al centro può essere effettuato in qualsiasi momento. Estensioni del polo montate alla superficie del piano magnetico rendono possibile, anche la presa omogenea di pezzi irregolari o di parti grezze, permette di essere bloccati senza distorsione. EPRadial 600:N. 65047 EPRadial 800:N. 63541 EPRadial 1000:su richiesta EPRadial 1250:su richiesta

Le transporteur aimant SH (de production allemande) et HL sont adaptés pour le transport de tôles d'acier et des pièces oxycoupées à arêtes tranchantes. Le transporteur aimant HL 60-CE | HL 60-CEL magnétisé et démagnétisé sur pression d'un bouton, tient néanmoins comme un aimant permanent. La possibilité de commande (commande radio) du HL 60-CEL est située dans la poignée de la barre de maintien prolongée. HL 10:Réf. 104 HL 20:Réf. 25031 SH 12:Réf. 101 HL 60-CE:Réf. 60347 HL 60-CEL:Réf. 69924