Produse pentru licol 5500 bitum (4)

Fluid Col Multi-purpose additive powder, to add to a suitable mixture of binders and aggregates, for the on-site production of mortars, grouts and concretes that are self-levelling, rheoplastic, controlled shrinkage or moderately expansionary, high mechanical strength, chemical and waterproofing. The physical-chemical action of Fluid Col is an interaction of positive contributions and modifications: drastic reduction of the A/C ratio, shrinkage-resistant action, superpozzolanic action and reaction of ultrafine fillers (MICROSIL 90), which transforms unstable, soluble, readily reactive calcium hydroxides into stable, insoluble, chemically and mechanically resistant hydrous calcium silicates. Preparation of mortars, grouts, rheofluid concretes, shrinkage-compensated or moderately expansionary, high mechanical, watertightness and chemical stability performance, for structural slubs, anchoring machines, road joints, etc. Add the product in a concrete mixer, mixer truck or mixer, together with the remaining anhydrous components of the mixture: cement and aggregates, any polypropylene and/or steel fibres, etc. The indicative dosage, depending on the type of conglomerate to be packaged and its purposes, varies between 12% and 15% of the weight of the cement. After a first mixing, add the mix water and mix thoroughly, until you obtain a homogeneous whole and free of lumps. The cement dosage must not be less than 350 kg/m³. Fluid Col is perfectly compatible with the addition of fibre d steel and/or polypropylene fibres READYMESH, for the preparation of conglomerates composite s, fibre reinforced. Add 10 - 15% of Fluid Col to the weight of the cement present in the mixture. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Premixed adhesive based on cement class C2 TE S1 for the indoor and outdoor installation of floor and wall coverings, with high workability, extended open time and increased adhesion and good capacity to absorb the substrate’s deformation, zero vertical slip. Specific for floor and wall coverings also non-absorbent, natural stones, overlapping non-absorbent materials, large formats on large surfaces screeds with insertion of underfloor heating, for application of porcelain stoneware at low thickness.

Liquid product based on lithium silicates, which was created for the protective, consolidating and porosity reducer treatment of concrete, mineral, brick and stone substrates. It guarantees optimal durability and adhesion strength, resistance to UV rays, chemical agents and mechanical stresses. The result of the application allows to obtain a rapid hardening of the surface as well as a revived and homogeneous appearance of the same. The product has a negligible environmental impact thanks to the low VOC content (<50 g / l) and is practically odorless. Protective, reinforcing, water repellent treatments of concrete, mineral and stone supports. Specific product for revitalizing, simultaneously providing a great consolidation and an annulment of the dust produced in concrete supports, interstices, brick, stone or mixed arches, present in taverns, public premises and of historic monuments interest. The application surfaces should be clean, free of incrustations, dust etc. A preliminary wash with distilled water or steam it's recommended. The support should be dry when applying. Apply the product as it is, with low pressure sprayer or brush with long bristles. Keep the substrate wet with Consilex Idrofix for at least 20 minutes during application. If applied on floors, wait 24 hours before passing on the treated support. The reinforcing contribution will be completed after 2-3 weeks of treatment. From 0,20 to 1,00 kg of Consilex Idrofix per square meter of surface to be treated, based on the porosity of the support.

An anti-dust chemical/mechanical revitalising hardener for concrete flooring and screeds, consisting of an aqueous solution of mineral silicates and fluosilicates, activated by specific wetting agents. It is applied in several coats of decreasing dilution in water, with a brush or mechanical “scrubber”. Specific anti-dust treatments for industrial flooring or concrete slabs that have lost their original “vitality”. It reacts with the calcium compounds, soluble and unstable, present in of concrete products, transforming them into new stable, insoluble and resistant compounds. Consequent increases in resistance to wear and tear of the order of 200% -400%, significant increases in chemical stability, resistance to freeze-thaw cycles etc. Reactive impregnations for stabilising chemical and mechanical structures and concrete products. Hardening, anti-dust, anti abrasive and anti-corrosion treatments for concrete floorings. Adjustment of the chemical and mechanical performance of products for the industrial, rural and livestock construction (on horizontal surfaces). Apply, preferably with a brush or with "washer dryer" machine on the basis of the following indications: - Porous surfaces: repeated applications of a solution of water and QL Fluosil at a ratio in 1:1 - Compact surfaces: apply three coats, with decreasing dilution with water. 1a coat 1:3, 2a coat 1:2, 3a coat 1:1. The consumption of QL Fluosil will be proportional to the absorption of the floor to be treated. Indicatively a porous surface will consume about 400 g/m², while a surface with normal porosity will consume 250-300 g/m². Leave the product to dry between one coat and the next and then, after the last coat, wash with copious amounts of water. Protect glass and aluminium surfaces during application. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface".