Produse pentru fara (17)

Syntech Pavicrom SBV Colored two-component finish, permeable to water vapour, based on epoxy resins in water dispersion. Ideal for the pigmented coating of industrial floors and concrete constructions in general with residual humidity and without vapor barrier. Surfaces treated with Syntech Pavicrom SBV are easy to clean and guarantee excellent resistance to mechanical wear, as well as being highly resistant to water, alkaline solutions, detergents and hydrocarbons (petroleum, diesel, petrol, etc.) . Protective and decorative painting of concrete floors, restoration of the color of old resin floors, glazing of wall skirting boards, etc. Ideal for mechanical workshops, manufacturing industries, warehouses and factories in general where high chemical and mechanical resistance is required. It can be used both indoors and outdoors. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating. In case of restoration, use suitable mortars and products suitable for the system beforehand. Wait for the drying times before applying the next coat. The tensile strength must not be less than 1.5 N/mm². Existing paints, coatings or paints, cement grout residues, release agents, oils, greases, silicones, etc. they can be removed mechanically by sandblasting, blasting, hydroblasting or chemical removal. Cracks and fissures In case of static cracks, use Syntech Primer EP-W for sealing. The sealing of dynamic cracks or cracks larger than 4-5 mm must be assessed on site. Generally they can be grouted with elastomeric materials or act as expansion joints. Grouting and spot repairs Any holes or repairs to portions of concrete can be made with mortars from the REPAR line or by applying epoxy mortar made with Syntech Primer EP-W and quartz mastics. Apply a coat of Syntech Primer EP-W as a bonding primer, then proceed to seal and repair the damaged and broken concrete by applying the epoxy mortar. Any small filling of holes and cracks can be done by applying Syntech AS 21 epoxy mortar. Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Primer for concrete Syntech Pavicrom SBV can be applied directly to cementitious substrates as the product diluted with a maximum of 25% by weight of clean water acts as an anchoring primer. Resin coatings The application of Syntech Pavicrom SBV on resinous and multilayer systems must always be preceded by sanding the entire surface to promote and guarantee optimal adhesion of the product to the support. Combine the two components in the indicated mixing ratio. Add component B (hardener) to component A (base) and mix well until a completely homogeneous product is obtained. It is advisable to start mixing briefly with an electric drill at low speed and then intensify the stirring up to a maximum of 300-400 rpm. Leave the emulsion obtained to rest in the container, respecting the following induction times: at 15°C ~ 20 minutes at 25°C ~ 15 minutes at 30°C ~ 10 minutes The product can be applied uniformly using a spray gun or short-haired roller to avoid accumulations of material which could give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area to obtain a uniform film and eliminate any accumulations of product. Apply the first coat of Syntech Pavicrom SBV diluted with a maximum of 25% by weight of clean water as primer. The dilution must be carried out under mechanical stirring, adding the necessary quantity of water at the end of the induction time. Do not dilute the product further during application if it thickens it means that the use time has expired. Create a new emulsion with highly mixed material. Wait at least 12 hours, then apply the second one Colored finish diluted with a maximum of 20% weight of clean water, respecting the consumption and thicknesses indicated. It is possible to create non-slip finishes by adding quartz or hollow glass spheres. From 0.15 to 0.20 kg of Syntech Pavicrom SBV for each square meter of surface to be covered, for each coat. Pail 2.5 kg [A] - Pail 5 kg [A] - Pail 3 kg [B] - Pail 6 kg [B] - Kit: 1 Pail 2.5 kg [A] + 1 Pail 3 kg [B] - Kit: 1 Pail 5 kg [A] + 1 Pail 6 kg [B]

Le buste idonea contatto per alimenti che forniamo, sono neutre senza stampa oppure personalizzabili con il vostro marchio, sono vendute in scatole di cartone, possono contenere alimenti conservati a temperatura ambiente oppure in cella freezer

Monitorare VGA M8 Monitor VGA LCD 8” a colori (800×600) ideale per applicazioni POS in ambito Retail; attacco VESA posteriore per fissaggio senza la base da tavolo inclusa. Cavi RS232 e VGA da 2.8 mt. Monitor capacitivo True Flat da 15" | Monitor touch resistivo ELO da 15 pollici Monitor True Flat estremamente resistente. Alloggiamento pressofuso in alluminio, gestione cavi a scomparsa, pannello frontale ermetico contro acqua e polvere, supporto 2nd display e MSR.

Il pecorino in forma Rosso delattosato è un formaggio fresco trattato in crosta con concentrato di pomodoro, di forma scodellata del peso di circa kg.1,5 Disponibile in forma intera sfusa ; confezione sottovuoto intera kg.1,5; sottovuoto a metà kg 0.750; sottovuoto a quarti di forma kg. 0.350.

Idee brillanti per trasmettere il cuore e l'anima della tua attività. Emoziona il tuo pubblico, catturane l’attenzione, stregalo con il tuo fascino.

DIE HASELNUSSSORTE MORTARELLA HAT EINE LÄNGLICHE FORM DER MITTELDÜNNEN SCHALE, DIE HELLBRAUN GESTREIFT IST. ER HAT EINEN EBENFALLS SUBOVALEN, IM UNTEREN TEIL LEICHT ABGEFLACHTEN SAMEN, DER SICH DURCH EIN GLEICHMÄSSIGES ELFENBEINWEISSES FRUCHTFLEISCH,EIN ANHALTENDES AROMA UND EINEN SÜSSEN GESCHMACK AUSZEICHNET.DIESE BESONDERE HASELNUSSSORTE WIRD ZWISCHEN DER ZWEITEN AUGUSTDEKADE UND MITTE SEPTEMBER GEERNTET.

Da Officine Locati la porta basculante che "allarga il garage" eliminando i contrappesi laterali: guide di soli cm. 4 ciascuna! Grande robustezza ed affidabilità nel tempo, oltre alla sicurezza antintrusione. Facili da montare, senza opere murarie, le porte basculanti prodotte da Officine Locati sono in acciaio zincato, anche verniciato a forno con polveri epossidiche in tinta RAL, manuali o motorizzate.

Syntech HAG Flex Mono-component semi-flexible, expanding (increases its initial volume of about 10 times) polyurethane resin, free from solvents, perfect for sealing small and large water leaks in the concrete or in solid masonry in general by injection. Perfect for filling and sealing small cavities, joints and discontinuities subject to movement. In contact with water, SYNTECH H.A.G. FLEX forms a flexible polyurethane foam. The product increases its initial volume by about 10 times in contact with fresh water. If used in environments with the presence of sea water, the expansion will take place in any case but slightly reduced in volume. Technically, it is a mono-component product which reacts spontaneously with the water present in the masonry to be sealed. The speed of reaction with just water, however, would be very slow relative to the construction site requirements. It is therefore essential to use an expansion accelerator, sold in combination with the same resin (component B). The polyurethane foam resulting from injection operations, will keep its volume stable once expanded. A good resistance to hydraulic pressure in the water flow after about 1-2 minutes from the time the reaction took place. The formation of CO₂, typical of the polyurethane reaction, will further pressurise the system, thus favouring the penetration of the resin in the cracks and cavities. In a free environment, SYNTECH H.A.G. FLEX expands to about 10 times its initial volume. Stop the infiltration of water in underground spaces. Perfect for waterproofing filling small cavities, cracks, fissures, static and dynamic joints in concrete and in solid masonry in general. The application surfaces should be clean, free of incrustations, crumbling and non-adhering parts, dust, moss, moulds, etc. Prepare the appropriate injectors, usually "staggered" (from one side to the other of the discontinuity to be sealed). Preliminarily inject abundant water in the discontinuity until saturation (if not already present). Pour 100 g of component B for each kilogram of component A (ideal and recommended dosage), in a bucket. Mix the two components thoroughly with a hand tool (do not use a mixer drill). Keep in mind that the resin could react even with the environmental humidity, therefore, to reduce the waste of material it is advisable to prepare a quantity of mixture strictly necessary for the intended use from time to time (2-3 kg of mixture at a time may be more that sufficient). The mixture of SYNTECH H.A.G. FLEX and its catalyst can be injected with a manual or electric pump for monocomponent resins, at pressures ranging between 40 and 200 bar. The reaction speed can easily be adjusted based on the accelerator (component B) quantity. Adding a greater quantity of catalyst, compared to the recommended 10%, reduces the reaction time. Always clean the pump used thoroughly at the end of the operations with Nitro thinner and the specific lubricant detergent SYNTECH H.A.G. CLEANER. The consumption of the product depends on the size of the vacuum volume to be filled and on the expansive reaction that occurs after mixing the two components in relation to the amount of water present. Can 25 kg [A] - Plastic can 2.3 kg [B] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.3 kg [B]

Syntech HAG Eco Mono-component, enabled for contact with drinking water, semi-flexible, expanding (increases its initial volume of about 20 times) polyurethane resin, free from solvents, perfect for sealing small and large water leaks in the concrete or in solid masonry in general by injection. Perfect for filling large voids and loose stone foundations inside the walls. In contact with water, SYNTECH H.A.G. ECO, forms a semi-flexible polyurethane foam. The product increases its initial volume by about 20 times in contact with fresh water. If used in environments with the presence of sea water, the expansion will take place in any case but slightly reduced in volume. Technically, it is a mono-component product which reacts spontaneously with the water present in the masonry to be sealed. The speed of reaction with just water, however, would be very slow relative to the construction site requirements. It is therefore essential to use an expansion accelerator, sold in combination with the same resin (component B). The polyurethane foam resulting from injection operations, will keep its volume stable once expanded. A good resistance to hydraulic pressure in the water flow after about 1-2 minutes from the time the reaction took place. The formation of CO₂, typical of the polyurethane reaction, will further pressurise the system, thus favouring the penetration of the resin in the cracks and cavities. In a free environment, SYNTECH H.A.G. ECO expands to about 20 times its initial volume. Stop the infiltration of water in underground spaces. Perfect for waterproofing filling large cavities or loose stone foundations in the concrete and in solid masonry in general. The application surfaces should be clean, free of incrustations, crumbling and non-adhering parts, dust, moss, moulds, etc. Prepare the appropriate injectors, usually "staggered" (from one side to the other of the discontinuity to be sealed). Preliminarily inject abundant water in the discontinuity until saturation (if not already present). Pour 100 g of component B for each kilogram of component A (ideal and recommended dosage), in a bucket. Mix the two components thoroughly with a hand tool (do not use a mixer drill). Keep in mind that the resin could react even with the environmental humidity, therefore, to reduce the waste of material it is advisable to prepare a quantity of mixture strictly necessary for the intended use from time to time (2-3 kg of mixture at a time may be more that sufficient). The mixture of SYNTECH H.A.G. ECO and its catalyst can be injected with a manual or electric pump for monocomponent resins, at pressures ranging between 40 and 200 bar. The reaction speed can easily be adjusted based on the accelerator (component B) quantity. Adding a greater quantity of catalyst, compared to the recommended 10%, reduces the reaction time. Always clean the pump used thoroughly at the end of the operations with Nitro thinner and the specific lubricant detergent SYNTECH H.A.G. CLEANER. The consumption of the product depends on the size of the vacuum volume to be filled and on the expansive reaction that occurs after mixing the two components in relation to the amount of water present. Can 25 kg [A] - Plastic can 2.3 kg [B] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.3 kg [B]

Grout Garden Quick-setting cementitious mortar for assembling and fixing fence posts, rotating clothesline, etc…, in holes made in the ground… without mixing with a drill, whisk, cement mixer or other. Suitable for mounting and fixing fence posts, rotating clothesline, etc ..., in holes made in the ground without mixing with a drill, whisk, cement mixer or other. For the installation of the rapid mortar it is necessary to dig a sufficiently large hole or trench. The ground in which the hole will be made must be stable and well compacted. Before processing, the side and floor surfaces must be pre-wetted, avoiding the formation of puddles. The dry mix should be applied in layers of about 10-15 cm. With a hand watering can you can wet and compact the mortar with a trowel, considering a water requirement of about 3-3.5 liters for each 25 kg bag of Grout Garden. As soon as the water has completely penetrated into the mortar, we will proceed with the laying of another 10-15 cm layer, repeating the operation. Compact and smooth the surface of the mortar as well as possible. Depending on the temperature of the air and the environment, the hardening of the product will start after about 5 minutes. After about 1 hour, the hardened mortar can be drilled with a drill to fix any poles or signs. Complete hardening, like all cementitious materials, will be obtained after about 28 days. Approximately 19 kg / m² of Grout Garden for each centimeter of thickness to be created (approximately 1900 kg per cubic meter). Packaging: 25 kg bag Unit of Measure: €/kg

Nastri adesivi avana senza stampa, per chi deve chiudere scatole destinate ad essere stoccate in ambienti asciutti, in ambienti umidi, in ambienti aggressivi al di sotto dello zero come la surgelazione

Nastri adesivi bianchi senza stampa, per chi deve chiudere scatole destinate ad essere stoccate in ambienti asciutti, in ambienti umidi, in ambienti aggressivi al di sotto dello zero come la surgelazione

La scatola più conosciuta al mondo, la scatola modello americano, utile per svariati usi legati alla spedizione delle proprie merci, una scatola economica per tutti gli usi

Il pecorino in forma Vecchio delattosato è un formaggio stagionato pezzatura a scalzo dritto del peso di circa kg.1.9. Disponibile in forma intera sfusa;confezione sottovuoto intera 1.9 kg, sottovuoto a metà kg.0.950; sottovuoto a quarti di forma kg. 0.450. Disponibile anche in formato forma da 0.500 kg.

Il Marzolino delattosato, è un formaggio fresco di forma ovale del peso di circa kg 0.850; disponibile in forma intera sfusa; confezione sottovuoto intera kg 0.850; sottovuoto a metà kg 0.400.

Il pecorino in forma nero delattosato, è un formaggio semi stagionato trattato in crosta con concentrato di pomodoro, pezzatura a scalzo dritto del peso circa kg.2.00 Disponibile in forma intera sfusa; confezione sottovuoto intera 2.00 kg, sottovuoto a metà kg.1.00; sottovuoto a quarti di forma kg. 0.500.

DIE GESCHÄLTE HASELNUSS, VON EINEM SORGFÄLTIGEN SCHÄLUNGSPROZESS IN UNSERER FABRIK ERHALTEN, WIRD NACH KUNDENWUNSCH KALIBRIERT.(9-11, 11-13, 13-15 mm) DIE GESCHÄLTE HASELNUSSE KÖNNEN MIT EINEM SÜSSEN ODER GESALZENEM GERICHT KOMBINIERT WERDEN. DIE KÖNNEN AUCH ALS SNACK GENIESSEN WERDEN, ZWISCHEN MAHLZEITEN. REICH AN MINSERALSALZEN UND DIE PERFEKTE NATÜRLICHE ERGÄNZUNG FÜR ALLE SPORTLER. SIE WIRD VON DEN UNTERNEHMEN BENUTZT, ENTWEDER FÜR DEN DIREKTEN VERBRAUCH, ALS AUCH FÜR DIE WEITERE RÖSTUNGSTUFE.