Produse pentru epoxid compus in componenți (37)

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

DETAILING & PAINT CORRECTION

Eine industrielle Bodenbeschichtung, die dank ihrer Epoxidharz-Basis enorm chemikalienbeständig ist. In vielen Farben und den Versionen Säureresistent, Anti-Rutsch, Kalttrocknend, Rapid verfügbar.

Nummer Eins chemicals 2008 Yılından beri Kimya sektöründe edinmiş olduğu tecrübeler ışığında müşterilerine en iyi ürünü ve hizmeti sunma felsefesi ile yola çıkarak İSTANBUL tuzla’da A.O.S.B de Epoksi ve Poliüretan Yapı Sistemleri, Antikorrozif epoksi ve poliüretan çelik konstrüksiyon ürünleri, Ahşap ve Metal tekneler için epoksi ve poliüretan ürünler, Su bazlı polimer esaslı su yalıtım sistemleri İç ve Dış mekanlarda kullanılan kaplama sistemlerine yönelik ürünlerin üretimine devam etmektedir. Firmamız kaliteli üretim kaliteli ürün anlayışı ile Avrupa normlarına uygun laboratuar cihazları ve analiz ekipmanlarına sahip ARGE ve Kalite Kontrol Laboratuvarında konusunda uzman mühendis ve kimyager kadrosu ile günümüz dünyasındaki teknolojik gelişimleri yakından takip ederek ürünlerini sürekli geliştirmekte ve yenilikçi bir anlayış ile çalışmalarını sürdürmektedir.

Système époxy transparent. Dureté variable. Facile d'emploi. -> Application Décoration, décoration florale, imitation de liquide, simulation de cours d'eau en maquettes. Couleur : Transparent Ratio mélange : 100/100 Potlife : 70 min à 9h Temps avant démoulage : >48h TG°C : nc Unité de vente : 1 kit de 2kg Minimum de commande : 1 kit

Colles polymérisant à température normale ou par chauffage Température normal 50°C

Chesterton® Formbare Polymer-Flachdichtung 860 ist ein solide flexibles Dichtungsmaterial, welches Oberflächenunreinheiten ausfüllt, Leckage stoppt und nie nach der Aushärtung an der Oberfläche klebt.

Pardoseala epoxidica cu granule colorate Emex Quartz - See more at: http://www.e - Pardoseala Epoxidica Decorativa EMEX QUARTZ este un produs profesional, pe baza de rasini epoxidice fara solvent, disponibil intr-o gama infinita de modele obtinute prin inglobarea de granule de cuart sau marmura divers colorate in masa pardoselii. Acest tip de pardoseala se mai numeste si covor epoxidic. Produsul poate inlocui cu succes mozaicul sau gresia, avand in primul rand avantajul aspectului superior, dar fiind si o alternativa mult mai rezistenta atat la utilizare dar si in timp a acestora. Caracteristici principale: - Produs agrementat sanitar; - Aderenta excelenta la suport; - Etalare de exceptie; - Duritate excelenta; - Durabilitate mare; - Rezistenta mare la abraziune; - Rezistenta excelenta la uzura; - Rezistenta mare la agenti corozivi; - Rezistenta mare la hidrocarburi, medii acide sau alcaline.

Das Epoxidharz-System E30RB ist eine 2K Epoxi-Rollbeschichtung mit mittlerer Verarbeitungszeit für hochwertige Boden- und Wandbeschichtungen ähnlich RAL7032 kieselgrau.

Utilisation de la résine Coulée Couleur du mélange Blanche Viscosité du mélange à 20 °C > 1 000 CPs

EXCOR UNICO è un espanso morbido a celle aperte, imbevuto di VCI e di 5 mm di spessore. Grazie alla sua struttura a spugna, dispone di un’enorme superficie di erogazione e fornisce così all’imballaggio velocemente la giusta quantità di VCI. Negli imballaggi con pellicole di grande volume, l’espanso UNICO si impiega come rinforzo. L’espanso UNICO è disponibile in rotoli o fogli, non rilascia odori, è asciutto e resistente all’invecchiamento. Per fissare il prodotto sulle pareti o sui soffitti, su richiesta del cliente, EXCOR può dotare il prodotto di autoadesivo.

Adhésif pour collage de composite sur composite Recrée une couche d'inhibition pour une adhésion fiable entre composite et composite Avantages Application simple avec un pinceau Manipulation rapide et facile Recrée une couche d'inhibition Adhésion sûre Comment l'utiliser? GC COMPOSITE PRIMER est également appliqué pour une adhésion sûre lors de la caractérisation de dents artificielles et prothèses acryliques avec le système composite micro hybride GC GRADIA et GC GRADIA gum shades. Liste

DESCRIPTION Façacryl est une peinture de dispersion acrylique de haute qualité spécialement conçue pour les façades. Très bonne adhérence sur toutes les surfaces minérales et diverses. Bon pouvoir couvrant, ne jaunit pas, respirant, parfaitement lavable et bon tendu. Rendement (indicatif) : 6-9 m²/L, selon le support Valeurs limites de l’UE pour ce produit (COV) : Cat. A/a : 30 g/L (2010). Ce produit contient moins de 30 g/L de produits COV.

Our extensive expertise spans various applications, including model construction, prototyping, and the production of tools for manufacturing technology. Consistent High Quality and Color Accuracy Across Batches: Our unwavering commitment to consistently high quality and color accuracy across batches allows you, as a customer, to fully focus on the production of your product. Wide Standard Product Portfolio: With a broad standard product portfolio, we offer an impressive selection of materials and colors for various 3D printing applications. From classic materials like PLA, PET-G, ASA, ABS to High-Performance Biopolymers and wood filaments, we meet your most demanding requirements. Custom Manufacturing: Our flexibility is evident in the option for custom manufacturing. Decide not only on material and color but also on spool type and packaging size, whether it's a standard plastic spool, recycled plastic spool, or environmentally friendly cardboard spool.

CKW-freier, lösemittelhaltiger 2K-Kontaktklebstoff auf CR-Basis für Gummi, Metall, Gewebe, Neopren z.B. als Kaltklebstoff für Fördergurte, Verschleißschutzauskleidung, Trommel- / Walzenbelegung

Xypex Concentrate is the most chemically active product within the Xypex Crystalline Waterproofing System.When mixed with water, this light grey powder is applied as a cementitious slurry coat to above-grade or below-grade concrete, either as a single coat or as the first of a two-coat application. It is also mixed in Dry-Pac form for sealing strips at construction joints, or for the repairing of cracks, faulty construction joints and honeycombs. Xypex prevents the penetration of water and other liquids from any direction by causing a catalytic reaction that produces a non-soluble crystalline formation within the pores and capillary tracts of concrete and cement-based materials.

In einigen Bereichen der Industrie werden bestimmte Eigenschaften der Bodenbeschichtung gefordert. Eine dieser Eigenschaften ist die elektrische Ableitfähigkeit des Bodens.

Akrilik reçine esaslı, su bazlı, tek kompenantlı, kullanıma hazır, pozitif su basıncına dayanıklı, kaplama altı Kısmi Elastik su yalıtım malzemesidir. Yarı elastik ► Akrilik Reçine Esaslı, Fırça ve rulo uygulanır. ► Su Bazlı, Düşük sıcaklıklarda bile elastikiyetini korur. ► Tek Bileşenli, Yüksek aderans sağlar. ► Kullanıma Hazır, Kullanıma hazırdır. ► Yarı Elastik ► Düşük Sarfiyatlıdır > Beyaz

COMPLEXFLUIDE ha sido especialmente diseñado para inducir y estimular el desarrollo óptimo de las plantas para obtener resultados más rápidos y efectivos en el metabolismo. Actúa rápido y es altamente compatible con mezclas para aplicaciones foliares. La sinergia formada entre el PHC y los macroelementos NPK favorece la asimilación de estos nutrientes, mejorando el proceso fotosintético, lo que contribuye a un mayor crecimiento vegetativo y una fructificación de mayor calidad. Packs de: • 1000 L • 20 L • 10 L • 5 L Nitrógeno (N) total :6% p/p Nitrógeno (N) uréico:4% p/p Nitrógeno (N) amoniacal :2% p/p Pentóxido de Fósforo (P2O5) soluble en agua:6% p/p Óxido de Potasio (K2O) soluble en agua:6% p/p Cloruro (Cl):<0,3 Ph:6,5-7 Densidad (gr/cc):1,19

Parachim Vinylester en Polyester. Styreenvrije, twee-component chemische verankering. Voor elk type spanningsloze verankering in zowel droge als vochtige en massieve als holle materialen.

Mit unseren vielseitigen Beschichtungssystemen veredeln wir nicht Ihre Bauteile von einer einfachen Rostschutzgrundierung bis zu einem farblichen Deckanstrich.

I rivestimenti in PVD e CVD garantiscono un'ottima adesione al metallo duro ed una maggiore durata del prodotto. Essi possono essere applicati su richiesta del Cliente su trafile, spalle, sellette e blocchetti.

PROVIPLAST é um material autopolimerizável indicado para a confecção de peças protéticas provisórias como coroas, pontes, inlays, onlays e facetas.

Die IPA Polyschicht ist eine kuststoffmodifizierte Silikatbeschichtung mit höchster chemischer Beständigkeit und DIBT- Zulassung. Abscheider, Domschächte, Faultürme, LAU - Anlagen, Tankwannen, Waschstraßen etc. werden mit der IPA Polyschicht dauerhaft saniert.

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Liquid product based on lithium silicates, which was created for the protective, consolidating and porosity reducer treatment of concrete, mineral, brick and stone substrates. It guarantees optimal durability and adhesion strength, resistance to UV rays, chemical agents and mechanical stresses. The result of the application allows to obtain a rapid hardening of the surface as well as a revived and homogeneous appearance of the same. The product has a negligible environmental impact thanks to the low VOC content (<50 g / l) and is practically odorless. Protective, reinforcing, water repellent treatments of concrete, mineral and stone supports. Specific product for revitalizing, simultaneously providing a great consolidation and an annulment of the dust produced in concrete supports, interstices, brick, stone or mixed arches, present in taverns, public premises and of historic monuments interest. The application surfaces should be clean, free of incrustations, dust etc. A preliminary wash with distilled water or steam it's recommended. The support should be dry when applying. Apply the product as it is, with low pressure sprayer or brush with long bristles. Keep the substrate wet with Consilex Idrofix for at least 20 minutes during application. If applied on floors, wait 24 hours before passing on the treated support. The reinforcing contribution will be completed after 2-3 weeks of treatment. From 0,20 to 1,00 kg of Consilex Idrofix per square meter of surface to be treated, based on the porosity of the support.

Clorosmalt piscine Chlorinated rubber-based paint, plasticized with a glossy finish, specific for the creation of a protective coating for swimming pools, tanks, fountains, drainage basins, containment basins and metal structures. It can be applied directly to steel structures, concrete, cement plasters and surfaces even permanently immersed in water. Its high chemical and physical resistance make it an ideal coating resistant to chlorinated water, acidic and basic solutions, ozonated water, salt water, as well as UV rays and temperature changes even in aggressive industrial and marine environments. Suitable for the protection of carpentry, bridges, cranes, silos, etc. in industrial and marine atmospheres. It is supplied in the standard colors White, Light Blue and Sand, on request it can be supplied in other colours. The advantages of Clorosmalt Piscine are: Excellent resistance to chlorinated and ozonated water and acid and basic solutions Single-component product easy to apply Long protection of treated surfaces Suitable for covering large surfaces Good abrasion resistance Waterproof and easy to clean Does not favor the growth of algae High adhesive power and excellent coverage. Specially formulated for the painting of swimming pools, ornamental tanks, canals, fountains, lakes, tanks, and any cement or metal support that is heavily and permanently in contact with water. The application surfaces must be clean, free of dirt, crumbly, inconsistent or non-absorbent parts, dust, pre-existing paint, etc... The humidity of the support, measured with a carbide hygrometer, must not exceed 4%, to avoid the formation of surface defects or blistering of the applied product. Check for the presence of residual humidity using the plastic sheet method according to the ASTM D 4263 standard: fix a heavy polyethylene sheet with a size of at least 45x45 cm to the support with adhesive tape. 24 hours after its installation, lift the sheet and check for signs of humidity. Thoroughly homogenize the product by manually shaking the container before use or mechanically, taking care to use a clean tool free of potentially polluting substances. It can be applied by spray or with a short-haired roller in a homogeneous manner to avoid accumulations of material that could cause give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area in order to obtain a uniform film and eliminate any accumulations of product. On the adequately prepared support, apply two or more coats of Clorosmalt Piscine, taking care to respect the indicated consumption and thickness. From 0.30 to 0.40 kg of Clorosmalt Piscine for each square meter of surface to be painted (in two coats). Packaging: 10 kg bucket Unit of Measure: €/kg