Produse pentru echipamente laborator (394)

The UVpad E combines the benefits of the spectral measuring technology with a handheld and easy to operate radiometer. The UVpad E is technically based on our successful radiometer UVpad. With the external sensor and an optimized programming, it is even more precise and easier to operate. Use the spectroradiometer UVpad E for an accurate measurement of the UV irradiance and for comparisons of different UV lamps and UV LEDs. 512 photodiodes measure the spectrum in the wavelength range of 240 – 480 nm. The categorization in UVA, UVB and UVC is taken according to international standards and traceable. The calibration to only one light source is omitted. Spectral range:240 - 480 nm ± 5 nm Spectral bandwidth:2 nm Pixel distance:~0,5 nm Irradiance meas. range (typ.):2 - 5000 mW/cm² Irradiance meas. range (high power version):25 - 20000 mW/cm²

The mains-driven panel meter RM-32 provides a continuous and precise measurement of irradiance with preamplified UV sensors. The integrated electronics produce a signal voltage that is transmitted to the radiometer, so that inferences are minimized. Different UV and visible spectral ranges, measuring ranges, and output signals can be selected to match the measurement task. The current irradiance is shown on a 3.5-digit digital display. The lamp state with respect to two threshold values is indicated by LEDs. Two relay contacts can be used for switching warning and failure signals. With its optional USB, RS232 or RS485 interface the RM-32 can be used to monitor ultraviolet (UV) irradiance. Control of light sources and irradiation systems Precise measurement of irradiances UV monitor for process control and documentation Dimensions:DIN 43700 96 x 48 mm Depth:~ 115 mm Weight:410 g Mains:230 V, 50 Hz, 3 W Operating temperature:0 to 40 °C

The very high irradiances of up to 39,000 mW/cm² and the compact dimensions characterize the UV-LED Spots and allow extremely short process times. For this purpose, the UV-LED is focused at the desired working distance. The UV-LED Spot P is suitable for automated and manual bonding. For applications such as bonding, potting or fluorescence excitation, the wavelengths 365, 385, 395, 405 and 450 nm are available. With the variety of wavelengths as well as the exchangeable optics, you remain particularly flexible and can upgrade and change over at any time. For controlling the UV-LED Spot P, we offer the LedControl S as a table top device or the LedControl DC for DIN rail mounting. With the LedControl S and DC UV LED controllers, the ultraviolet LED output can be set between 2% and 100%. Wavelength:365, 385, 395, 405 o. 450 nm Dimensions, Spot P:Ø 15 x 143 mm Dimensions, Spot P short:Ø 15 x 60 mm Cable length:1,5 m Weight:~130 g

The RMD radiometer is one of the latest developments from Opsytec Dr. Gröbel GmbH. This easy-to-use radiometer is based on more than 30 years of experience in all areas of irradiation and illuminance measurement. It features a wide dynamic range and extremely low noise. For this purpose, the sensor already contains a multi-stage amplification, an extremely precise analog-to-digital converter and a temperature sensor. The memory contained in the sensor contains all sensor identifications and the calibration history. This allows several ultraviolet sensors and visible sensors to be used on the Radiometer RMD. A wide range of sensors is available for a wide variety of production and control processes. Two sensors can be read out simultaneously. Sensors for the evaluation of erythema-weighted radiation and multi-channel sensors are also available. The measurement data are clearly displayed on the graphic display. Spectral range:UVA, UVA+, UVBB Resolution:0,001 µW/cm² Dimensions:Ø 40 mm, h 35 mm Weight:160 g Connecting cable:2 m

The high-performance UV LED Solo P combines a compact, variable, and economic point light source for manual bonds in an ergonomic design. The UV LED Solo P requires no external control and can be operated directly with a mains power adapter. As all UV LEDs the Solo P is quickly switchable. WAVELENGTH, BEAM PROFILE, AND OPTIC The wavelengths of 365, 385, 395, 405, and 450 nm are available for different applications. In addition, several beam profiles with interchangeable optics are available. The UV radiation of high-power LED is focused in the desired working distance. The high irradiance of 24,000 mW/cm ² allows for short processing times. APPLICATIONS OF HIGH-POWER UV-LED SOLO P UV curing and bonding and UV sealing Micro curing Irradiation of biological samples Hairline or leak detection using fluorescence markers Wavelength:365, 385, 395, 405 or 450 nm Max. irradiance:> 24000 mW/cm² Dimensions:Ø 15 x 143 mm Weight:~130 g Operating voltage:100 - 240 V, 50/60 Hz

The PLC.D sensors are ready-to-install UV sensors with digital output. This enables reliable and repeatable irradiance measurements in UV systems. Due to the compact design and the eight spectral ranges, the sensors can be used for a wide range of applications, e.g. in packaging facilities sterilisation surface activation systems UV curing systems ageing tests and many other applications With the integrated 24-bit ADCs, the PLC.D sensors close the gap between industrial manufacturing and high-precision laboratory equipment. Measurements can be carried out in a simple yet safe way. RS-485 and USB are available as optional connections for this purpose. The data evaluation takes place directly in the PLC.D sensors, the measured values are protected against transmission errors by a CRC-16 check sums. Operation voltage:24 V (RS-485 / RS-232) Dimensions:80 x 40 x 20 mm Weight:150 g Connector:Built-in plug, M8, 8-pin Response time, max:200 ms

Xenon excimer lamps enable new, resource-saving and more efficient production possibilities. They are used in the field of surface treatment for matting, cleaning, surface activation or to save photoinitiators. For this purpose, the narrow-band spectrum around 172 nm is usually used to irradiate under inert gas conditions. Then the high photon energy is sufficient to split almost all organic compounds. The measurement of 172 nm (VUV) is an important component for process control and optimization. With the tinyTracker 172 we offer a calibrated band radiometer which is suitable for use in an inert atmosphere. The tinyTracker 172 is absolutely calibrated and measures the irradiance and irradiation dose of xenon excimer lamps directly at 172 nm. Due to its particularly flat design, the tinyTracker172 can be guided through the irradiation channels of UV belt dryers and other industrial equipment. Measuring range:0-200 mW/cm² Resolution:12 bit Recording time:up to 3 hours Sampling frequency:1 - 100 Hz, adjustable Photo detektor:GAP

Les béchers de mesure en PP sont pratiquement incassables et hautement transparents. Les béchers de mesure sont parfaitement adaptés comme supports de publicité pour des produits chimiques. Leur surface lisse permet également l'impression d'un logo ou d'un message publicitaire. Material:PP, transparent

tinyTracker dosimeters are autonomous instruments for irradiance and dose measurement in UV belt systems. Due to the particularly flat design of the tinyTracker, this can be performed by irradiation of UV conveyor dryers and other industrial equipment. The recording of values automatically starts when exceeding an adjustable minimum irradiance. The integrated radiometric sensors can be configured for different UV and visible spectral ranges. The integrated diffuser serves for cosine correction that is necessary in non-perpendicular irradiation. The sensors are calibrated to PTB. The data recording is done on a removable SD card, data transfer - via USB. The power is supplied by a Li-Ion battery that provides a recording time of up to three hours. The Li-Ion battery can be charged directly via the USB interface. An additional power supply unit is included. The analysis and data export are done conveniently using a PC. HIGHLIGHTS OF TRACKER FOR UV CONVEYOR BELTS Measuring range:0-200 mW/cm² or 0-2 W/cm² Resolution:12 bit Recording time:up to 3 h Dimensions tinyTracker:195 x 79 x 10 mm Operating temperature:up to 60 °C

Différents équipements peuvent être montés sur la tige télescopique (raccord à encliquetage). Chaque tige dispose d'une butée. Ainsi, il est impossible de provoquer une désolidarisation par accident d'une tige. Les tiges télescopiques ne permettent pas de rotation, pour une prise en main encore meilleure ! Tige télescopique 5355-0280, modèle extrêmement court – mais extensible jusqu'à 280 cm. Peut être rangé dans tout coffret ! Le puisard à tige télescopique est un système de prélèvement disposant de multiples équipements pour des applications diverses. Les équipements (bécher à angle variable, bécher sur balancier, porte-flacons, bécher en inox et épuisettes) sont raccordés par encliquetage sur la tige télescopique. Idéal pour le prélèvement en bassins, cuves, puits, plants d'eau, etc. Les tiges téléscopiques en aluminium réglables en longueur permettent d'atteindre une profondeur de 6 m. Longueur réglable graduellement de:65 cm - 600 cm

We offer LED technologies for existing applications. With our modular concept, combined with our calibration laboratory and in-house production we offer decisive development advantages. POSSIBLE REASONS FOR CUSOMIZED UV-LED: The system already exists. Standard products can’t be installed due to limited space. Irradiation from one direction is not sufficient The determination of irradiation wavelength has not yet taken place You are looking for a competent and independent partner YOUR ADVANTAGES WITH OPSYTEC UV-LED CUSTOMIZED SOLUTION: Development and production from a single source Ideal for small batches, tests and prototypes Wavelength 275 nm, 365 nm, 385 nm, 395 nm and 405 nm available Further wavelengths are possible Suitable sensor? We offer customer-specific solutions, too Reliable results through our own calibration laboratory Special solutions are beneficial - even for small quantities. Ask us!

Esta pinza de acero inoxidable está diseñada para los trabajos de máxima precisión en el laboratorio. La pinza es recta y tiene extremos sin punta y con rugosidades en la cara interior. Estas características permiten manipular con total precisión diferentes materiales, tejidos y muestras. La pinza de laboratorio está hecha de acero inoxidable y tiene rugosidades en el mango. Material:Acero inoxidable V2A (1.4301)

Mini-douche oculaire idéal pour le laboratoire, les stations de soutirage ou pour les postes de travail sur lesquels des substances agressives sont manipulées. Eyes Fresh peut être monté sur tout robinet d'eau froide existant. Une pression sur le bouton permet de passer d'une douche oculaire à un écoulement normal de l'eau pour le nettoyage (remise en fonction du mode douche oculaire lors de la fermeture du robinet d'eau). S'adapte sur un robinet d'eau avec filetage externe M22x1, 1/2" ou 3/8". S’il y a suffisamment de pression d'eau disponible, la puissance est conforme à DIN EN ISO 15154-2.

With the UV LED series L, we combine the benefits of the UV LEDS compared to the UV lamps; these are initial start, dimmability, long service life and a lower heat input with an economical UV LED system. Irradiances of up to 5,5 W/cm² are reached on the surface. The high irradiance enables short processing times. For different applications, wavelengths of 365nm, 385 nm, 395 nm, 405 nm, and 450 nm are available. That way, the UV LED series L can be optimal customized for the requirements of the photoinitiator. All wavelengths are available in five differently sized illumination areas from 10 x 100 mm, and 30 x 30 mm up to 200 x 100 mm. Customized versions are available too. Wavelength:365, 385, 395, 405, 450 nm Connections:Trigger, Interlock in Programming, optional:RS485, RS232 or USB Internal security circuit:Over-temperature, LED defect Cable length:3 m, up to 10 m (opt.)

The sampling set SteriPlast® Kit consists of ten sample spatulas or ten sample scoops and ten SteriBag Premium tamper-proof sample bags. Thus the SteriPlast® Kit is the ideal combination for sampling where purity and sterility is essential. All parts are sterilised by gamma rays and suitable for use with foodstuffs. The scoops or spatulas are clean room manufactured and individually packed. The sample bag SteriBag Premium has an integrated sealing and is liquid-tight. A unique tracking code on both the bag and the tear-off field guarantees complete documentation and traceability. SteriPlast® Kit including scoop 50 ml or spatula 150 mm insertion depth, and SteriBag Premium 300 ml.

Für exakte Laborarbeiten eignet sich die Edelstahlpinzette. Die Pinzette hat eine gerade Form mit stumpfen Enden, deren Innenseiten geriffelt sind. Dadurch lassen sich unterschiedliche Materialien, Gewebe oder Proben genau aufnehmen. Die Laborpinzette besteht aus Edelstahl und hat einen geriffelten Griff. Material:Edelstahl V2A (1.4301)

The light plastic forceps for single use allow for fatigue-free work. The clean room-manufactured lab assistants meet the highest standards and prevent cross-contamination or impurities in the sample being examined. The lab tweezers are suitable for chemical, pharmaceutical or cosmetic applications as well as the food industry and scientific uses. Pointed/angled shape The disposable forceps have fine, smooth, curved gripping tips. Different materials can be held and processed reliably with the pointed ends. Pointed shape The anatomical forceps have a straight tip, fluted on the inside. This makes it possible to grip sensitive materials reliably. Broad tip shape The disposable forceps have ends with a broad tip. The broad tip is smooth and blunt. It prevents the material from being damaged when it is gripped. Material:PS Colour:White, blue or blue detectable Overall length:130 mm

The use of ultraviolet-curing adhesives and compounds is constantly increasing. With the LedControl S UV LED controller, you remain flexible for future requirements. Due to the modular design, one UV LED lamp, up to five or even up to 16 UV LED lamps with different wavelengths can be operated and individually adjusted with one LEDControl S. For applications such as bonding, potting or fluorescence excitation, the wavelengths 365, 385, 395, 405 and 450 nm are available. With the variety of wavelengths, you remain particularly flexible and can upgrade and change over at any time. With several UV LED lamps, the irradiation can also be ideally homogenized to achieve the best possible uniformity. With the intelligent UV LED control, the power of the ultraviolet LED lamps can be individually adjusted between 2% and 100%. A timer for irradiation times between 0.01 s and 9999 s is already integrated. Dimensions:185 x 251 x 100 mm (S) Operating temperature:5 to 40 °C Storage temperature:-10 to 60 °C Humidity:< 80%, non-condensing Mains:100 - 240 V, 50/60 Hz

Client-specific UVC-Sensor Modification of our UVC-SE Sensors optical entrance nearer to the lamp Transmission measurement / calculation possible using UVC-SE and the UVCSE long sensor

L’assurance qualité commence par le contrôle à la réception des marchandises ! L’échantillonnage toutes couches de produits en vrac n’est plus un problème avec le préleveur de poudres et de granulés PowderProof®. PowderProof® est la solution professionnelle éprouvée pour le prélèvement mobile de poudres et granulés. L'unité d'entraînement robuste permet de raccorder et de remplacer sans problème différentes cannes d'échantillonnage et spirales de transport. Ce concept modulable permet l'emploi de PowderProof® pour les granulés et poudres, dans des tonneaux, fûts, BigBags ou sacs. Des accessoires utiles tels des paniers à bouteilles, des sachets pour échantillons et des étiquettes d'obturation close-it permettent un prélèvement encore plus simple et sûr. PowderProof® avec pic pour installation horizontale, pour le prélèvement d'échantillons de sacs, avec pic pour installation verticale, pour le prélèvement de récipients ouverts tels que des fûts, tonneaux ou BigBags. Modèle:pour poudre jusqu'à 2 mm ou pour granulés de 2 à 4 mm Canne: horizontal ou vertical Profondeur de plongée:300 mm, 600 mm, 900 mm ou 1200 mm

With our UV probes, we offer calibrated probes for measuring of the irradiance in areas that are difficult to access. The UV probes are available in three versions and several standard lengths of 15 cm to 60 cm. With an outer diameter of only 6 mm, the UV probes are a perfect supplement for the precise radiometers RMD, as well as for the spectral radiometers UVpad E and SR900. All UV probes come with a diffuser, which enables the absolute measurement of irradiance and which ensures the required cosine correction during a non-perpendicular irradiation. The UV probes are, together with the radiometers, traceably calibrated to the PTB, recalibratable and are supplied with a calibration certificate by the factory. By using appropriate materials, an outstanding long-term stability is reached. A repair service and parts supply is of course available for many years. Diameter, probe:Ø 6 mm Length, probe:15 cm or 30 cm Weight:~ 200-350 g Operation temp., probe:0 to 200 °C

Retaining valve with embossed directional arrow or printed in black. With conical nozzles. Various uses. Operating Temperature:0 to +40 °C

The water pressure-proof UVC-SE sensors serve as robust, long-term stable measuring heads for the precise measurement of UV-C irradiances of low-pressure mercury lamps and amalgam lamps in water disinfection and wastewater systems. The sensor can be exposed to pressure of up to 10 bar. A long-term, stable high-sensitivity photo diode with a large active area of 1 cm² is used. This provides low noise and improved sensitivity, below 260 nm, compared to SIC sensors. Superior corrosion resistance and long-term stability is also achieved through the use of appropriate materials. No aging is determined over a period of one year. The sensors are calibrated with traceability to the PTB, the German national test authority. The integrated electronics produce a signal voltage that is transmitted to the PLC or panel meter RM-32, so that inferences are minimized. Operating voltage and output signal can be selected to match the measurement task or PLC interfaces. Measuring range:0 - 1000 W/m² Spectral range:180 - 280 nm Dimensions:see drawing Housing material:Stainless steel Weight:~420 g

Detectable SteriPlast® scoops, made of blue polystyrene, are produced (except for the 1000 ml scoop) and assembled in our class 7 clean room (10,000), individually packaged for disposable use and then sterilised by gamma rays. Detectable scoops are ideal for powders, granulates and pastes. These scoops, spatulas, spoons and scrapers are not only coloured blue but also have a special additive in the material that makes them visible to metal detectors or X rays. These products can therefore be rejected with standard systems for checking for foreign objects, even though they are made of plastic. Material:PS

Mini ducha lavaojos ideal para laboratorios, unidades de trasiego u otros lugares en los que se trabaja con sustancias agresivas. Eyes Fresh se puede montar en cualquier grifo de agua fría convencional. Con solo pulsar un botón se puede cambiar de ducha lavaojos al goteo de agua para el lavado (al cerrar el grifo se vuelve a la función de ducha lavaojos). Compatible con grifos de agua con rosca exterior de M22x1, 1/2" o 3/8". Si la presión de agua es suficiente, rendimiento según la norma DIN EN 15154-2.

Cuchara para la toma de muestras de sustancias en polvo, productos intermedios y materias primas en la industria farmacéutica. Para ello se deben emplear materiales de alta calidad con una superficie especial, con el fin de evitar la contaminación cruzada. Nuestra Pharma-spoon cumple estas exigencias. Fabricado en acero inoxidable V4A (1.4404), superficie pulida a mano (no electropulida). El excelente pulido del Pharma-spoon proporciona ventajas decisivas. Longitud total:650 mm

When decanting flammable liquids without the machines and containers involved in the process being sufficiently earthed, electrostatic build-up can occur, which for many substances can result in fire or an explosion. Bürkle’s Anti-static set ensures easy and reliable earthing. The Anti-static set consists of three colour-coded connecting copper cables with clamps in a handy plastic case.

Mini-Augendusche ideal für Labor, Abfüllstationen oder alle Arbeitsplätze, an denen mit aggressiven Stoffen gearbeitet wird. Eyes Fresh lässt sich auf jeden herkömmlichen Kaltwasserhahn montieren. Durch Knopfdruck kann von Augendusche auf Perlwasser zum Waschen umgestellt werden (wird beim Schließen des Wasserhahns wieder auf Augenduschfunktion zurückgestellt). Passend für Wasserhähne mit Außengewinde M22x1, 1/2" oder 3/8". Bei ausreichendem Wasserdruck Leistung gemäß DIN EN 15154-2.

Barrel pump made of stainless steel with discharge tube. The Bürkle barrel pump made of stainless steel AISI 304 (1.4301) is suitable for filling combustible and easily flammable liquids. The barrel pump can conduct electricity and therefore fulfills the requirements for handling flammable liquids in combination with the accessory antistatic set. The PTFE gaskets ensure long-term and maintenance-free use. Pumping capacity approx. 9–22 l/min, dependent on pump length. The wide range of accessories makes it possible to adapt the pump to very different requirements. Material:Stainless steel Immersion tube Ø:32 mm

Detectable SteriPlast® spoons, made of polystyrene, are produced in our class 7 clean room (10,000), individually packaged for disposable use and then sterilised by gamma rays. The detectable spoons are available in two sizes, 2.5 ml (similar to a teaspoon) and 10 ml (similar to a tablespoon), and are ideal for sampling powders, granulates and fluids. These scoops, spatulas, spoons and scrapers are not only coloured blue but also have a special additive in the material that makes them visible to metal detectors or X rays. These products can therefore be rejected with standard systems for checking for foreign objects, even though they are made of plastic. Material:PS