Produse pentru component 2 epoxid (13)

Transparent epoxy coating of two components with high chemical and mechanical resistance for the protection and decoration of floors. Does not contain solvents (100% solids). Features High transparency. Excellent resistance to yellowing and water staining. Very good resistance to solvents, detergents, acids and diluted bases, gasoline, diesel, brake fluid and lubricating oils. High mechanical resistance. Antidust effect.

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

ADLER PUR-based coatings are modern solvent-based systems that meet the most demanding standards in furniture and interior decoration. The best resistance, both for chemical and mechanical stresses and strains, as well as ease of application and use are the special features of this type of coating system. ADLER offers the best choice of PUR-based coatings for the most diverse types of wood as well as the most varied design concepts. Premium quality and efficient use are always ensured in the process. In this manner, you can meet almost any need or requirement for the surface as desired by your customers.

L'IDS EPOXYKLEAN 100 est spécialement formulé pour le nettoyage et le décapage des résines époxy, PU, etc. employées pour le collage et jointoiement de revêtements céramique ou autres supports. Ce produit permet l’élimination des vernis époxy, vernis 2K, revêtement anticorrosion, etc. employés notamment dans l’industrie automobile pour le nettoyage des installations d’application de peintures et résines (pistolet, pompes, buses, zones de préparation, sols, etc.). L’IDS EPOXYKLEAN 100 est une solution neutre qui permet le ramollissement des résines même durcies. Sa formulation est totalement exempte de produits CMR. L’IDS EPOXYKLEAN 100 ne corrode pas les métaux ferreux et non ferreux et n’attaque pas les joints dans leur masse. Produit fabriqué en France.

Das Epoxidharz-System E30RB ist eine 2K Epoxi-Rollbeschichtung mit mittlerer Verarbeitungszeit für hochwertige Boden- und Wandbeschichtungen ähnlich RAL7032 kieselgrau.

Nummer Eins chemicals 2008 Yılından beri Kimya sektöründe edinmiş olduğu tecrübeler ışığında müşterilerine en iyi ürünü ve hizmeti sunma felsefesi ile yola çıkarak İSTANBUL tuzla’da A.O.S.B de Epoksi ve Poliüretan Yapı Sistemleri, Antikorrozif epoksi ve poliüretan çelik konstrüksiyon ürünleri, Ahşap ve Metal tekneler için epoksi ve poliüretan ürünler, Su bazlı polimer esaslı su yalıtım sistemleri İç ve Dış mekanlarda kullanılan kaplama sistemlerine yönelik ürünlerin üretimine devam etmektedir. Firmamız kaliteli üretim kaliteli ürün anlayışı ile Avrupa normlarına uygun laboratuar cihazları ve analiz ekipmanlarına sahip ARGE ve Kalite Kontrol Laboratuvarında konusunda uzman mühendis ve kimyager kadrosu ile günümüz dünyasındaki teknolojik gelişimleri yakından takip ederek ürünlerini sürekli geliştirmekte ve yenilikçi bir anlayış ile çalışmalarını sürdürmektedir.

Utilisation de la résine Coulée Couleur du mélange Blanche Viscosité du mélange à 20 °C > 1 000 CPs

Das hochwertige, ungesättigte Laminierharzsystem HP-P21LS auf ISO/NPG-Basis ist niedrigviskos, wachsfrei und luftseitig klebrig aushärtend. Polyesterharz Laminiersystem (wachsfrei) / HP-P21LS Das Polyesterharz HP-P21LS ist eine ungefüllte, vorbeschleunigte, niedrigviskose 2-Komponenten Kombination von Harz und Härter mit kurzer Verarbeitungszeit . Verarbeitungszeit: 15-20min Eigenschaften und Einsatzgebiete: - Hochwertiges, ungesättigtes Polyesterharz auf Basis ISO/NPG - vorbeschleunigt, thixotrop, luftseitig klebrig aushärtend - Sehr gute mechanische Eigenschaften - Als Tränk- und Laminierharzsystem einsetzbar - Schwimmbadbau, Boots- und Schiffskörperbau - Geeignet für Handauflege-, Faserspritz-, Schleuder- und Wickelverfahren - Milieu Harz, also verminderte Styroldampf-Abgabe, LSE (Low styrene emission) - Erhöhte Wärmestandfestigkeit - Erhöhte Wasser- und Chemikalienbeständigkeit weitere Informationen unter www.hp-textiles.de

The highly optimized Dual KVM Extender over IP has a range of 150m/492ft at a resolution of 1920x1200 @60 Hz and is available infiber as dual version. For point to point or in Matrix Switching Systems up to 1000 endpoints The perfect tuning of kvm-tec video compression with a low latency time enables a delay-free transmission of the signals. USB and video is transmitted via fiber cable. Due to the DVI extension Full HD videos can be transmitted in real time. USB memory, sound, RS232, analog VGA- as DVI transfer are already included. With the included switching upgrade up to 1000 endpoints, the MAXflex Extender can be integrated into a matrix switching system up to 1000 endpoints in conjunction with a standard network switch. kvm-tec Switching Manager - the intelligent software enables convenient management and intuitive operation of KVM extenders in the switching system. A Windows PC or Tablet with network interface is required for commissioning and operating the software.

Epoxy waterborne paint bicomponent cured with polyamide, for protection of floors of concrete, metal structures, etc.

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.