Transparent epoxy coating of two components with high chemical and mechanical resistance for the protection and decoration of floors. Does not contain solvents (100% solids). Features High transparency. Excellent resistance to yellowing and water staining. Very good resistance to solvents, detergents, acids and diluted bases, gasoline, diesel, brake fluid and lubricating oils. High mechanical resistance. Antidust effect.

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Wir fertigen CNC-Frästeile aus Acrylglas in engen Toleranzen und mit hoher Oberflächengüte für den industriellen Einsatz im Maschinenbau sowie in der Analyse-, Medizin- und Verpackungstechnik. Wir fertigen CNC-Frästeile aus Acrylglas mit einfachen bis hin zu komplexen Geometrien auf Basis von 3D-Daten. Zu unserem Fertigungsbetrieb in Garbsen gehören u. a. 3-Achs- und 5-Achs-CNC-Bearbeitungszentren, auf denen der Werkstoff präszise und mit hoher Oberflächengüte bearbeitbar ist. Für spezielle Anwendungen, z. B. in der Analyse-, Medizin- und Verpackungstechnik setzen wir spezielle Werkzeuge für glasklares Fräsen ein. Teileabmessungen: • 3-Achsbearbeitung: max. 1524 x 660 x 635 mm • 5-Achsbearbeitung: max. 762 x 508 x 508 mm • CNC-3-Achs-Portalfräsbearbeitung: 4500 x 2000 mm Zusätzliche Serviceleistungen: • Polieren • Bedrucken • Gravieren

Système époxy transparent. Dureté variable. Facile d'emploi. -> Application Décoration, décoration florale, imitation de liquide, simulation de cours d'eau en maquettes. Couleur : Transparent Ratio mélange : 100/100 Potlife : 70 min à 9h Temps avant démoulage : >48h TG°C : nc Unité de vente : 1 kit de 2kg Minimum de commande : 1 kit

PRO-SET® Laminier-Epoxide gehören zu einem vielseitigen System aus flüssigen Harzen und Härtern und eignen sich für viele Nasslaminier-Verfahren. Mit PRO-SET Laminier-Epoxiden lassen sich leichte, leistungsstarke Verbundbauteile herstellen, die dauerhaft höchsten zyklischen Belastungen unter härtesten Umweltbedingungen ausgesetzt werden können. Bei Raumtemperatur entwickeln diese Epoxide ausgezeichnete physikalische Eigenschaften und können zur Verbesserung der Eigenschaften nachgehärtet werden. Zu den weiteren Merkmalen gehören: Verkleben vieler verschiedener Arten von Kernmaterialien einschließlich Holz, Metall und alle Verstärkungsfasern Ausgezeichnete Feuchtebeständigkeit Hervorragende Wärmebeständigkeit Hervorragende Dauerfestigkeit

ADLER PUR-based coatings are modern solvent-based systems that meet the most demanding standards in furniture and interior decoration. The best resistance, both for chemical and mechanical stresses and strains, as well as ease of application and use are the special features of this type of coating system. ADLER offers the best choice of PUR-based coatings for the most diverse types of wood as well as the most varied design concepts. Premium quality and efficient use are always ensured in the process. In this manner, you can meet almost any need or requirement for the surface as desired by your customers.

L'IDS EPOXYKLEAN 100 est spécialement formulé pour le nettoyage et le décapage des résines époxy, PU, etc. employées pour le collage et jointoiement de revêtements céramique ou autres supports. Ce produit permet l’élimination des vernis époxy, vernis 2K, revêtement anticorrosion, etc. employés notamment dans l’industrie automobile pour le nettoyage des installations d’application de peintures et résines (pistolet, pompes, buses, zones de préparation, sols, etc.). L’IDS EPOXYKLEAN 100 est une solution neutre qui permet le ramollissement des résines même durcies. Sa formulation est totalement exempte de produits CMR. L’IDS EPOXYKLEAN 100 ne corrode pas les métaux ferreux et non ferreux et n’attaque pas les joints dans leur masse. Produit fabriqué en France.

Die Serie HP-E3000GL besitzt eine Zulassung vom Germanischen Lloyd für den Bau von Booten und Windkraftanlagen und ist individuell mit verschiedenen Härtern auslieferbar.

- Remplissage - Calage de lest Utilisation de la résine Coulée Couleur du mélange Incolore Viscosité du mélange à 20 °C de 600 à 1 000 CPs Durée de vie en pot sur 500 g à 20 °C > 3h Transition vitreuse TG1 en °C de 80 à 100 °C Température minimale de polymérisation 40 °C

Das Epoxidharz-System E30RB ist eine 2K Epoxi-Rollbeschichtung mit mittlerer Verarbeitungszeit für hochwertige Boden- und Wandbeschichtungen ähnlich RAL7032 kieselgrau.

Nummer Eins chemicals 2008 Yılından beri Kimya sektöründe edinmiş olduğu tecrübeler ışığında müşterilerine en iyi ürünü ve hizmeti sunma felsefesi ile yola çıkarak İSTANBUL tuzla’da A.O.S.B de Epoksi ve Poliüretan Yapı Sistemleri, Antikorrozif epoksi ve poliüretan çelik konstrüksiyon ürünleri, Ahşap ve Metal tekneler için epoksi ve poliüretan ürünler, Su bazlı polimer esaslı su yalıtım sistemleri İç ve Dış mekanlarda kullanılan kaplama sistemlerine yönelik ürünlerin üretimine devam etmektedir. Firmamız kaliteli üretim kaliteli ürün anlayışı ile Avrupa normlarına uygun laboratuar cihazları ve analiz ekipmanlarına sahip ARGE ve Kalite Kontrol Laboratuvarında konusunda uzman mühendis ve kimyager kadrosu ile günümüz dünyasındaki teknolojik gelişimleri yakından takip ederek ürünlerini sürekli geliştirmekte ve yenilikçi bir anlayış ile çalışmalarını sürdürmektedir.

ISONEM SHINE FLOOR est une résine de sol autolissante à base de polyuréthane et de solvant (bi composants).

Beschichtbar sind Feinblech, Baustahl (auch verzinkt), Alu-Blech, Alu-Druckguss, Magnesiumguss, Glas und Kunsttsoff, in Abhängikeit von der Temperaturbeständigkeit. Pulverlacke sind lösungsmittelfrei und werden mit elektrostatischen Spritzpistolen aufgebracht und je nach Empfindlichkeit und Chemie der Pulverlacke und der zu beschichteten Teile werden sie zwischen 130 und 220°C ausgehärtet. Folgende Vorbehandlungen sind möglich: • Gelb - und Grünchromatierung • Zinkphosphatierung • chromfreie Konversation Vorteile • hochwertiger Korrosionsschutz • stark mechanisch belastbar • keine Umweltprobleme, da lösungsmittelfrei und Rückgewinnung des Oversprays • sehr gute chemische Beständigkeit • hohe Steinschlagfestigkeit • als Polyesterpulver sehr UV-beständig • dekorative Oberflächen in fast allen Farbtönen, Glanzgraden und Strukturen

Colle de contact transparente à base polyuréthane - spécial PVC doux Pour double encollage de matériaux divers, durs ou flexibles, comme la plupart des matières synthétiques (PVC souple, PVC, ABS, plexi, polycarbonate), bois, panneaux de revêtements décoratifs stratifiés, placage et collage sur champ, nez de marches et marches d’escalier, plinthes en PVC, cuir, liège, textile, métaux entre eux ou sur bois, pierre, béton, plâtre, métal et autres supports lisses et non poreux. Spécifiquement pour des applications dont la couche de colle ou le joint de colle reste visible : comme le collage sur verre ou plexi. Aussi idéal pour la réparation de bâches, toiles de tente et pour matériaux gonflables en PVC souple. Prête à l'emploi, transparente au séchage, pas de trace brune, utilisation aisée à la brosse et au peigne à colle, force d'adhérence progressive rapide, résistante à l'humidité à la chaleur et au froid (-10°C jusqu'à +70°C) Résiste aux acides légers et bases Sans...

Chemikalien für die Manuelle Verarbeitung von Röntgenfilmen. Entwickler Structurix G 128 ist ein einteiliger, flüssiger Entwickler für die manuelle Entwicklung industrieller Röntgenfilme. Fixierer Structurix G 328 ist ein einteiliger, flüssiger Fixierer für die manuelle Entwicklung industrieller Röntgenfilme. Der Fixierer G 328 enthält keine Härter.

Support for concrete slabs made by recycled antischock (HIPS) material. Using area: door and window support of construction. 120*80*3 mm to 120*80*16 mm plastic support:support for concrete slabs

Aus den CAD Daten drucken wir im 3-D Druck Ihre Teile und giessen Sie in verschiednen Materialien bis zu einer Größe von 12x12x25 cm Größe: 12x12x25cm

Silikon eignet sich ideal für die Herstellung von wiederverwendbaren Formen. Insbesondere dann, wenn im Formenbau selbsttragende, stabile und dennoch flexible Formen gefragt sind, ist das Material unschlagbar. Durch die guten Eigenschaften von Silikon Kautschuk sind selbst komplexe Gegenstände mit mehrdimensionalen Hinterschneidungen perfekt in großer Detailgenauigkeit reproduzierbar. Für die Herstellung von Formen wird heute vorwiegend raum-temperaturvernetzendes RTV Silikon eingesetzt. Das Material ist selbsttrennend, die Entformung der Gießlinge dadurch unkompliziert umsetzbar. In einigen Fällen empfiehlt sich die Anwendung von Trennmitteln zur besseren Entformbarkeit.

MODSTEEL Ready-made wall panels are a newly invented wall block technique that is easy to use when building prefabricated homes as well as conducting interior space re-shaping in homes or workplaces. It can also be used in sheathing building walls in a safe and almost effortless manner. Our ready-made wall panels do not require lots of workmanship as it can be easily customized and cut into different shapes and sizes. Specifications The main components of the ready-made walls are gypsum board frames from each side that is then filled with expended polystyrene (EPS) a material that increases the insulation level of the wall. We also use a light cemented foam filling instead of traditional concrete in order to have better heat and sound insulation. The walls are totally fire proof even when exposed to direct fire which makes them a very safe choice for homes and places that include children, elderly and valuable material every panel weighs 350kg/m3.

Epoxy waterborne paint bicomponent cured with polyamide, for protection of floors of concrete, metal structures, etc.

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Utilisation de la résine Coulée Couleur du mélange Blanche Viscosité du mélange à 20 °C > 1 000 CPs

Das hochwertige, ungesättigte Laminierharzsystem HP-P21LS auf ISO/NPG-Basis ist niedrigviskos, wachsfrei und luftseitig klebrig aushärtend. Polyesterharz Laminiersystem (wachsfrei) / HP-P21LS Das Polyesterharz HP-P21LS ist eine ungefüllte, vorbeschleunigte, niedrigviskose 2-Komponenten Kombination von Harz und Härter mit kurzer Verarbeitungszeit . Verarbeitungszeit: 15-20min Eigenschaften und Einsatzgebiete: - Hochwertiges, ungesättigtes Polyesterharz auf Basis ISO/NPG - vorbeschleunigt, thixotrop, luftseitig klebrig aushärtend - Sehr gute mechanische Eigenschaften - Als Tränk- und Laminierharzsystem einsetzbar - Schwimmbadbau, Boots- und Schiffskörperbau - Geeignet für Handauflege-, Faserspritz-, Schleuder- und Wickelverfahren - Milieu Harz, also verminderte Styroldampf-Abgabe, LSE (Low styrene emission) - Erhöhte Wärmestandfestigkeit - Erhöhte Wasser- und Chemikalienbeständigkeit weitere Informationen unter www.hp-textiles.de