Produse pentru • i (107)

Syntech Poliurea Primer – Epoxy SYNTECH POLIUREA PRIMER - EPOXY is a two-component primer based on modified epoxy resins and special hardeners, solvent-free. Specially formulated to provide the right compromise between impregnation and wettability of the support to which, once applied, it forms a well-bonded layer. Adhesion promoter for epoxy, polyurethane and polureic coatings, adhesion promoter for porous and deteriorated substrates, consolidating agent for cement and concrete. The support on which the polyurea or resinous system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Carefully mix component A to allow the correct homogenization of the fillers present; then combine it with component B in a suitable and large container. Then mix the compound with a mechanical stirrer at low speed until a homogeneous mixture is obtained. When the support is ready, apply SYNTECH POLIUREA PRIMER - EPOXY using rollers, brushes or spatulas trying to obtain a dry film. From 350 to 700 g for each square metre, based on the intervention carried out on the support (bush-hammering, shot peening, etc.), the porosity of the support itself and the incorporation or not of quartz sand in the particle size and quantity proportionate to the intervention to be implemented. Can 20 kg [A] - Canister 4 kg [B] - Kit: 1 Can 20 kg [A] + 1 Canister 4 kg [B]

ART. 15 CERNIERE QUADRE IN ACCIAIO ZINCATO – perno fisso Confezione:100 Dimensioni (mm):50 x 50 x 1,0 Pollici:2

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Syntech Poliurea Primer – Pur SYNTECH POLIUREA PRIMER-PUR is a single-component polyurethane primer with a base of low viscosity solvent, polyurethane resins and special isocyanates that, once applied, form an elastic film that adheres to the substrate. The processing times of this product range from 90 to 120 minutes, based on the percentage of ambient humidity. SYNTECH POLIUREA PRIMER-PUR offers a support for coatings and waterproofing in general. Intermediate adhesion promoter for two-time applications of polyureas, elastomeric products, etc. The surface of the substrate must be dry, properly cleaned, free from any debris and friable or detached parts. All substrates must have a degree of humidity not greater than 5%. The surface temperature during application must be at least +5° C above dew point. If necessary, depending on the surface, the following interventions are recommended: Bush-hammering Milling Sandblasting Shot Blasting Water-blasting Hydro-jet Cleaning Any contamination (water, dirt, dust, etc.) will have to be carefully removed before coating. Mix the product with mechanical stirrer, being sure that the least possible amount of air is incorporated. Prevent the product from coming into contact with air or moisture. When the substrate is ready, apply SYNTECH POLIUREA PRIMER-PUR in the amount needed. Pay attention to the presence of condensate. In certain cases, whilst the product is still wet, complete a dusting of 0.5–0.8 quartz. From 80 to 120 grams of SYNTECH POLIUREA PRIMER-PUR per square metre of surface to be treated. Can 20 kg

ART. 808 CERNIERE EXTRAPESANTI IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):65 x 65 x 2,0 Pollici:2 ½ x 2 ½

ART. 323 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):35 x 25 x 0,8

ART. 838 CERNIERE PESANTI IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):45 x 35 x 1,2 Pollici:1 ¾

ART. 804 CERNIERE EXTRAPESANTI IN ACCIAIO ZINCATO – perno levabile Confezione:24 Dimensioni (mm):50 x 50 x 1,6 Pollici:2 x 2

ART. 838 CERNIERE PESANTI IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):50 x 40 x 1,3 Pollici:2

ART. 323 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):63 x 35 x 0,9 Pollici:2 ½

ART. 323 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):40 x 29 x 0,9 Pollici:1 ½

ART. 317 CERNIERE QUADRE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):45 x 45 x 0,9 Pollici:1 ¾

ART. 804 CERNIERE EXTRAPESANTI IN ACCIAIO ZINCATO – perno levabile Confezione:24 Dimensioni (mm):100 x 100 x 2,5 Pollici:4 x 4

ART. 804 CERNIERE EXTRAPESANTI IN ACCIAIO ZINCATO – perno levabile Confezione:6 Dimensioni (mm):125 x 125 x 3,0 Pollici:5 x 5

ART. 808 CERNIERE EXTRAPESANTI IN ACCIAIO ZINCATO – perno fisso Confezione:12 Dimensioni (mm):90 x 90 x 2,5 Pollici:3 ½ x 3 ½

ART. 317 CERNIERE QUADRE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):57 x 57 x 0,9 Pollici:2 ¼

ART. 808 CERNIERE EXTRAPESANTI IN ACCIAIO ZINCATO – perno fisso Confezione:12 Dimensioni (mm):90 x 75 x 2,5 Pollici:3 ½ x 3

ART. 330 CERNIERE LUNGHE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):26 x 90 x 1,3 Pollici:3 ½

ART. 10 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:100 Dimensioni (mm):25 x 20 x 0,7 Pollici:1

ART. 323 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):25 x 20 x 0,8 Pollici:1

ART. 317 CERNIERE QUADRE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):70 x 70 x 1,0 Pollici:2 ¾

ART. 321 CERNIERE MEZZE QUADRE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):80 x 60 x 1,2 Pollici:3 ¼

ART. 838 CERNIERE PESANTI IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):57 x 40 x 1,3 Pollici:2 ¼

ART. 804 CERNIERE EXTRAPESANTI IN ACCIAIO ZINCATO – perno levabile Confezione:12 Dimensioni (mm):90 x 90 x 2,5 Pollici:3 ½ x 3 ½

ART. 323 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:120 Dimensioni (mm):20 x 15 x 0,7 Pollici:¾

ART. 323 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):57 x 30 x 0,9 Pollici:2 ¼

ART. 838 CERNIERE PESANTI IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):63 x 45 x 1,3 Pollici:2 ½

ART. 330 CERNIERE LUNGHE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):34 x 180 x 2,0 Pollici:7 ¼

ART. 321 CERNIERE MEZZE QUADRE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):50 x 40 x 0,9 Pollici:2

ART. 323 CERNIERE STRETTE IN ACCIAIO ZINCATO – perno fisso Confezione:24 Dimensioni (mm):90 x 50 x 1,2 Pollici:3 ½